Flying the new sequences

Terry Clendennen tclendennen at hot.rr.com
Tue Jun 7 17:03:11 AKDT 2005


I still haven't found these new sequences.Where are they?
----- Original Message ----- 
From: "Ron Van Putte" <vanputte at cox.net>
To: <discussion at nsrca.org>
Sent: Tuesday, June 07, 2005 2:58 PM
Subject: Re: Flying the new sequences



On Jun 7, 2005, at 9:59 AM, Bob Kane wrote:

> I'm having more trouble with the slow roll after the
> figure 9 . . . . . . .

Hmmm, I must be getting better.  I haven't had a problem with that one
either.  I WAS having trouble with the 1/4, 1/2, 1/4 Roll until I
realized that I wasn't putting in enough rudder on the first point and
was trying to roll too fast.

Ron Van Putte

>
> --- Grow Pattern <pattern4u at comcast.net> wrote:
>
>> It is a tough maneuver to draw correctly in the sky.
>> That's why it is in at the level I guess. In FAI
>> they throw in a couple of 1/2 rolls to use up your
>> 45 degree lines.
>>
>> On a different subject. Is anyone finding it hard to
>> present the reverse knife-edge after the top hat in
>> masters this year?
>>
>> Eric.
>>   ----- Original Message -----
>>   From: John Ferrell
>>   To: discussion at nsrca.org
>>   Sent: Tuesday, June 07, 2005 8:50 AM
>>   Subject: Re: Flying the new sequences
>>
>>
>>   It sounds pretty tricky. If the first radius on
>> the push is not the "right amount" the line
>> length/cross is bunged.
>>
>>   Like the figure M, it is merciful there are only
>> 10 points to lose!
>>
>>   John Ferrell
>>   http://DixieNC.US
>>
>>     ----- Original Message -----
>>     From: Grow Pattern
>>     To: discussion at nsrca.org
>>     Sent: Tuesday, June 07, 2005 8:08 AM
>>     Subject: Re: Flying the new sequences
>>
>>
>>     A golf ball is more akin to the current P-05
>> "Goldfish" standing on end. An ice-cream cone has
>> much steeper sides and ends in a point at center.
>> The golf ball has a cross-over point at center of
>> the two straight 45 degree equal length lines.
>>
>>     FAI describes it as - Golf ball from top:  Push
>> to a 45 degree downline, pull through ¾ of an inside
>> loop to a 45 degree upline and push to recover
>> upright.
>>
>>     Regards,
>>
>>     Eric.
>>       ----- Original Message -----
>>       From: Wincons at aol.com
>>       To: discussion at nsrca.org
>>       Sent: Tuesday, June 07, 2005 12:05 AM
>>       Subject: Re: Flying the new sequences
>>
>>
>>       In a message dated 6/6/2005 11:03:17 P.M.
>> Central Daylight Time, patterndude at comcast.net
>> writes:
>>         The golf ball should really be named the ice
>> cream cone, but it wouldn't fit on the call sheets
>> easily.  In this case it's a 45 degree downline, a
>> 1/2 loop, a 45 degree upline back to center.  Now
>> help me with a spring coil!!!!
>>         --Lance
>>       Maybe 270 degrees 3/4 loop, not 180 deg
>> half-loop?
>>
>>       Brian ;)
>
>
> Bob Kane
> getterflash at yahoo.com
>
> __________________________________________________
> Do You Yahoo!?
> Tired of spam?  Yahoo! Mail has the best spam protection around
> http://mail.yahoo.com
> =================================================
> To access the email archives for this list, go to
> http://lists.f3a.us/pipermail/nsrca-discussion/
> To be removed from this list, go to http://www.nsrca.org/discussionA.htm
> and follow the instructions.
>
> List members email returned for mailbox full will be removed from the 
> list.
>

================To access the email archives for this list, go to
http://lists.f3a.us/pipermail/nsrca-discussion/
To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.

List members email returned for mailbox full will be removed from the list.



=================================================
To access the email archives for this list, go to
http://lists.f3a.us/pipermail/nsrca-discussion/
To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.

List members email returned for mailbox full will be removed from the list.



More information about the NSRCA-discussion mailing list