[SPAM] Re: Kavan starter dissassembly ? [PMX:] [PMX:]

[Pascale, Mike]

If you have a broken stator wire the best thing is chunk it but if you can
repair the wire try it my self I'd get a new one when you need one its not
going to work and it will not put up the rpm you might need the gears are
worn the grease will only take up.002  
good luck 
Mike 
From: discussion-request at nsrca.org [mailto:discussion-request at nsrca.org] On
Behalf Of Paul Horan
Sent: Tuesday, July 12, 2005 4:41 PM
To: discussion at nsrca.org
Subject: Re: [SPAM] Re: Kavan starter dissassembly ? [PMX:] [PMX:]



Mike,
    The gears and everything else has some dirt on it.  Not filthy but there
has been substantial wear due to debris getting into the gears and breaking
a wire on one winding.  
Paul

----- Original Message ----- 
From: Pascale, Mike <mailto:VPASCAL at citgo.com>  
To: discussion at nsrca.org <mailto:discussion at nsrca.org>  
Sent: Tuesday, July 12, 2005 4:02 PM
Subject: RE: [SPAM] Re: Kavan starter dissassembly ? [PMX:]

If the gears are clean use lithium White grease They sell this at Auto parts
store in 4 oz tubes remember a little goes along way.  

-----Original Message-----
From: discussion-request at nsrca.org <mailto:discussion-request at nsrca.org>
[mailto:discussion-request at nsrca.org] On Behalf Of Paul Horan
Sent: Tuesday, July 12, 2005 3:10 PM
To: discussion at nsrca.org <mailto:discussion at nsrca.org> 
Subject: Re: [SPAM] Re: Kavan starter dissassembly ? [PMX:]


Dave,
    I have it re-assembled except for lubing the gears.
    What grease should I use on the planetary gears ?  The main shaft is
steel but the planetary gears are nylon, epoxy or plastic.
Thanks,
Paul

----- Original Message ----- 
From: Rick Wallace <mailto:rickwallace45 at hotmail.com>  
To: discussion at nsrca.org <mailto:discussion at nsrca.org>  
Sent: Tuesday, July 12, 2005 2:51 PM
Subject: [SPAM] Re: Kavan starter dissassembly ?


You can also make a 'spanner' out of a flat tip screwdriver you don't care
much about -- a little dremel work to take out the center of the blade and
you're there... 


>From: DaveL322 at comcast.net <mailto:DaveL322 at comcast.net> 
>Reply-To: discussion at nsrca.org <mailto:discussion at nsrca.org> 
>To: discussion at nsrca.org <mailto:discussion at nsrca.org> 
>Subject: Re: Kavan starter dissassembly ?
>Date: Tue, 12 Jul 2005 18:59:59 +0000
>
>I believe what you need is a "spanner" wrench to loosen the nuts at the
back end of the starter - they are the bolts that appear at the front of the
body.  I made my own wrench from a piece of .125" aluminum.  A skinny set of
needle nose pliers might also work.  You will have some fun putting it back
together - the brushes are spring loaded against the commutator and need to
be "pinned" open via the pinholes in plastic case/housing on the back end of
the body.
>
>Good luck,
>
>Dave
>
>-------------- Original message --------------
>
> > My Kavan starter has some trash in the planetary gears. I have removed
the
> > cone holder in the front but am at a loss how I
> > further dissassemble it. There appears to be two bolts that go from the
rear to
> > the front of the body; but, I cannot find the screw
> > head.
> > Can anyone help ?
> > Thanks,
> > Paul
> >
> > =================================================
> > To access the email archives for this list, go to
> > http://lists.f3a.us/pipermail/nsrca-discussion/
> > To be removed from this list, go to http://www.nsrca.org/discussionA.htm
> > and follow the instructions.
> >
> > List members email returned for mailbox full will be removed from the
list.
> >



The information transmitted is intended only for the person or entity to
which it is addressed and may contain confidential and/or privileged
material. Any review, retransmission, dissemination or other use of, or
taking of any action in reliance upon, this information by persons or
entities other than the intended recipient is prohibited. If you received
this in error, please contact the sender and delete the material from any
computer.


The information transmitted is intended only for the person or entity to
which it is addressed and may contain confidential and/or privileged
material. Any review, retransmission, dissemination or other use of, or
taking of any action in reliance upon, this information by persons or
entities other than the intended recipient is prohibited. If you received
this in error, please contact the sender and delete the material from any
computer.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.f3a.us/pipermail/nsrca-discussion/attachments/20050713/b69e9d2e/attachment.html