receiver antenna and wire placement

[David Harmon]

I change all my antennas to Teflon coated wire. 
No chafing with this wire.

Regards

Dave Harmon
NSRCA 586
K6XYZ[at]comcast[dot]net
Torrance, Ca.

-----Original Message-----
From: discussion-request at nsrca.org [mailto:discussion-request at nsrca.org]
On Behalf Of John Ferrell
Sent: Monday, February 23, 2004 3:17 PM
To: discussion at nsrca.org
Subject: Re: receiver antenna and wire placement

In my experience the insulation chaffed through and then the wires
chaffed
through. Two inches of wire just is not enough to fly on.

John Ferrell
http://DixieNC.US

----- Original Message ----- 
From: "PPandelaers" <ppandelaers at pandora.be>
To: <discussion at nsrca.org>
Sent: Monday, February 23, 2004 2:06 PM
Subject: RE: receiver antenna and wire placement


> Can anyone explain why this is a problem? The antenna-wire is
> plastic-covered.
>
> ;-)
> Patrick
>
>
> -----Oorspronkelijk bericht-----
> Van: discussion-request at nsrca.org
[mailto:discussion-request at nsrca.org]
> Namens ronlock at comcast.net
> Verzonden: maandag 23 februari 2004 17:53
> Aan: discussion at nsrca.org
> Onderwerp: Re: receiver antenna and wire placement
>
> Aong same idea, to keep battery and servo wires from
> chafing against fiberglas and composite materials,
> you can line the fuse area with a sheet of paper.
>
> later, Ron Lockhart
> > It works fine.
> > Take care that the exposed antenna wire cannot chafe against the
fiber
> glass
> > fuse, the last pattern airplane I lost sufferred that!
> >
> > John Ferrell
> > http://DixieNC.US
> >
> > ----- Original Message ----- 
> > From: "JonAlan Wise" <wise at alaskalife.net>
> > To: <discussion at nsrca.org>
> > Sent: Monday, February 23, 2004 12:05 AM
> > Subject: receiver antenna placement
> >
> >
> > > Hi all, What is the best way to run the receiver antenna on a
composite
> > > fuse pattern plane? I am building a Temptation, I`m thinking of
putting
> > > the antenna in a tube inside the fuse. Will this work or will it
create
> > > radio reception problems? Any other ideas? Thanks Jon Wise
> > > Anchorage, Alaska
> > >
> > > =====================================
> > > # To be removed from this list, send a message to
> > > # discussion-request at nsrca.org
> > > # and put leave discussion on the first line of the body.
> > > #
> > >
> > >
> >
> >
> > =====================================
> > # To be removed from this list, send a message to
> > # discussion-request at nsrca.org
> > # and put leave discussion on the first line of the body.
> > #
> >
> =====================================
> # To be removed from this list, send a message to
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
>
>
>
> =====================================
> # To be removed from this list, send a message to
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
>
>


=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#


=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#