F3A Biplanes have a future!

John Ferrell johnferrell at earthlink.net
Wed May 14 05:36:14 AKDT 2003


Many vehicals will accept a fully assembled Bipe.
Disadvantage becmes an advantage...

John Ferrell
6241 Phillippi Rd
Julian NC 27283
Phone: (336)685-9606
johnferrell at earthlink.net
Dixie Competition Products
NSRCA 479 AMA 4190  W8CCW
"My Competition is Not My Enemy"

----- Original Message ----- 
From: "Henderson,Eric" <Eric.Henderson at gartner.com>
To: <discussion at nsrca.org>
Sent: Tuesday, May 13, 2003 7:13 AM
Subject: RE: F3A Biplanes have a future!


The only snag that I have found with bi-planes is the assembly at the field!
Four ailerons?  wing struts? etc. I sold a very good flying Ultimate and the
16 screws it took to assemble! I prefer one wing screw and two aileron leads
....Hmmmmm.... can I adapt???

Regards,

Eric.



-----Original Message-----
From: discussion-request at nsrca.org
[mailto:discussion-request at nsrca.org]On Behalf Of Adam Glatt
Sent: Tuesday, May 13, 2003 1:15 AM
To: discussion at nsrca.org
Subject: Re: F3A Biplanes have a future!


That makes three (publically known) biplane projects going on right now.
Just when you think you've got the best.... ;>  Time to spend more money.

I'm rather torn on this biplane issue.  Should FAI add a new rule that
outlaws them?  On one hand, I'm sure they will improve our flights, but on
the other I don't want them to be advantage over the planes we have now.
Kind of like changing the 2m size limit to 2.5m.  The guys with the big
factories behind them will have an advantage, while the rest of us will be
alienated.  Going to biplanes might be no different than going to 2.5m, only
it isn't against the rules.  Or, it might be like the switch to 2m planes
from the .60 planes.  I would hate to go back to a 0.60 after flying a 2m.

That said, I want a biplane.  I do expect they will fly better, which is
certainly a good thing, and someone has to develop them before I get to fly
it.

Still divided, but practicing as much as possible anyways,
Adam Glatt

----- Original Message -----
From: "PENNISI Peter" <Peter.Pennisi at publicworks.qld.gov.au>
To: <discussion at nsrca.org>
Sent: May 12, 2003 8:17 PM
Subject: F3A Biplanes have a future!


>
> Hi all,
>
>
> I had to opportunity to watch a F3A biplane fly for a short while in the
> hands of a very capable pilot last weekend. The model was built by a local
> kit manufacturer who adapted a set of wings to Carrera 2000 (Designed by
> Peter Goldsmith)as an experiment.
>
> The model was flown briefly through the P03 schedule until an unfortunate
> problem resulted in the model having to land minus wings on one side of
the
> fuse (More on that later) Anyway the flight looked very impressive
> especially in the broader speed envelope the model was capable of flying
in.
> The model was powered with a YS140DZ and weighed about 10.5pounds.
>
> The very experienced F3A pilot commented how impressed he was with the
model
> and felt it was already better than his current monoplane. Particular
> comments he made was that it spins, stall turns and rolls great snaps
would
> have been great until half the wing was ripped off as a result of
> overstressing.
>
> What this pilot did as the wings tore off was truly impressive. With the
> wings completely ripped off from one side of the fuse he had the
initiative
> to throttle up and fly the model in knife-edge and fly it around to make a
> crash landing approach. The end result was a few scratches to the fuse and
a
> broken prop. This was one of the most impressive things I have seen.
>
> It is a pity I didn't have my video camera with me as it certainly would
> have been great to see over and over again.
>
> I was very sceptical about F3A biplanes in Pattern until I saw this model
> fly on the weekend. I have no doubt that will be taken seriously at the
next
> world champs.
>
> Follow this link to view the model prior to it crashing.
>
> http://www.qpfa.org.au/neil/a_couple_of_stories_from_behind_.html
>
> Regards,
>
> Peter

=====================================
# To be removed from this list, send a message to
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#

============# To be removed from this list, send a message to
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#



=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#



More information about the NSRCA-discussion mailing list