Help: Webra TruTurn Adapter Bushing Problem

[Gray E Fowler]

No-9 tons will do the job.



Gray Fowler
Principal Chemical Engineer
Composites Engineering




glenn hatfield <randy10926 at comcast.net>
Sent by: discussion-request at nsrca.org
01/08/2003 12:32 PM
Please respond to discussion

 
        To:     discussion at nsrca.org
        cc: 
        Subject:        Re: Help: Webra TruTurn Adapter Bushing Problem


You will make it fit.  That sounds a little strong to me.  Are you 
going to use a 10-ton press to make it fit?

Personally I use a washer on my Webra.

Randy


----- Original Message -----
From: Gray E Fowler <gfowler at raytheon.com>
Date: Wednesday, January 8, 2003 12:41 pm
Subject: Re: Help: Webra TruTurn Adapter Bushing Problem

> Keith
> 
> Bring the engine and the bushing to me. It will make the bushing 
> fit here 
> at work.
> 
> 
> 
> Gray Fowler
> Principal Chemical Engineer
> Composites Engineering
> 
> 
> 
> 
> "Keith Black" <tkeithb at attbi.com>
> Sent by: discussion-request at nsrca.org
> 01/08/2003 10:51 AM
> Please respond to discussion
> 
> 
>        To:     <discussion at nsrca.org>
>        cc: 
>        Subject:        Re: Help: Webra TruTurn Adapter Bushing 
> Problem
> 
> I've already tried pressing the bushing down with the prop nut and 
> it 
> didn't work, it was too tight. I tried both a plastic and metal 
> bushing. I 
> thought that maybe I could force the plastic one with the prop nut 
> but 
> that didn't work either.
> 
> Take a look at the following link to see a picture of what I'm 
> talking 
> about: 
> http://www.fototime.com/217F0696EE7CE3E/standard.jpg
> Thanks,
> Keith
> 
> ----- Original Message ----- 
> From: Gray E Fowler 
> To: discussion at nsrca.org 
> Sent: Wednesday, January 08, 2003 8:32 AM
> Subject: Re: Help: Webra TruTurn Adapter Bushing Problem
> 
> 
> He means that the unthreaded portion at the thrust washer is 
> slightly 
> larger in diameter.  It is a very snug fit. You probably have only 
> tried 
> to slide this on with your fingers, when you may have to use the 
> prop nut 
> to get it on. Try using the prop nut and a spacer and if it does 
> not go on 
> pretty easy-stop. 
> It should fit-All of mine are plastic center spacers. 
> I have two Bully's which of couse are Webras, on one an APC prop 
> slides on 
> over that portion of the shaft, the other one requires using the 
> prop nut 
> to get even the prop seated over that unthreaded portion of the shaft.
> 
> 
> 
> Gray Fowler
> Principal Chemical Engineer
> Composites Engineering 
> 
> 
> 
> s.vannostrand at kodak.com 
> Sent by: discussion-request at nsrca.org 
> 01/08/2003 08:20 AM 
> Please respond to discussion 
> 
>        To:        discussion at nsrca.org 
>        cc: 
>        Subject:        Re: Help: Webra TruTurn Adapter Bushing 
> Problem
> 
> 
> 
> Welcome back Keith.  I think you are saying the crankshaft needs a 
> few 
> more threads.  I have used a washer spacer in the past, but not on 
> this 
> engine setup.  I use the Vortech spinner nut and APC 17 x XX and 
> never had 
> a problem. 
> --Lance 
> 
> 
> 

=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#



-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.f3a.us/pipermail/nsrca-discussion/attachments/20030108/6ed35375/attachment.html