EconoKote vs. MonoKote

[John Crozier]

 i  will pardon your backing
----- Original Message -----
From: "wgalligan" <wgalligan at cnbcom.net>
To: <discussion at nsrca.org>
Sent: Thursday, February 13, 2003 3:05 PM
Subject: Re: EconoKote vs. MonoKote


> I am backing your pardon...
>
> You have been backing up to that camel again havent you Amir?
>
> > What backing???
> >
> > Amir
> >
> >
> > > I hate to ask...but you did remove the backing from the Momokote......
> > > ----- Original Message -----
> > > From: "Atwood, Mark" <atwoodm at paragon-inc.com>
> > > To: <discussion at nsrca.org>
> > > Sent: Thursday, February 13, 2003 1:33 PM
> > > Subject: RE: EconoKote vs. MonoKote
> > >
> > >
> > > Hey Paul,
> > >
> > > I'm a huge advocate for "low" heat...but don't be afraid to use
"enough"
> > > heat. Balsa is an exceptional insulator (it's heavily used on
> > refrigeration
> > > ships) so you can use reasonable heat without worrying about the foam.
> > Just
> > > don't crank the heat to high and hold it in one spot too long or you
can
> > get
> > > a dip.   But moderate heat is more than acceptable, and even high heat
on
> > > occasion if needed as long as it's not stationary.
> > >
> > > I've been covering foam wings with Monokote for a long time and never
> > melted
> > > the foam.
> > >
> > > Mark
> > >
> > >  -----Original Message-----
> > > From: Paul Reed [mailto:paul at judco.net]
> > > Sent: Thursday, February 13, 2003 1:25 PM
> > > To: discussion at nsrca.org
> > > Subject: EconoKote vs. MonoKote
> > >
> > > Does anyone out there have any experience using EconoKote for foam
core
> > > wings? My wing cores are honeycombed and I am having trouble with
> > Monokote.
> > > The MonoKote especially the white is not adhering well to the balsa
even
> > > though the surface has been cleaned thoroughly with compressed air and
a
> > > tack rag. Your advice and experience will be appreciated.
> > >
> > > Regards,
> > > Paul Reed
> > > Quality Coordinator
> > >
> > > =====================================
> > > # To be removed from this list, send a message to
> > > # discussion-request at nsrca.org
> > > # and put leave discussion on the first line of the body.
> > > #
> > >
> > >
> > > ============# To be removed from this list, send a message to
> > > # discussion-request at nsrca.org
> > > # and put leave discussion on the first line of the body.
> > > #
> > >
> > >
> > >
> > > =====================================
> > > # To be removed from this list, send a message to
> > > # discussion-request at nsrca.org
> > > # and put leave discussion on the first line of the body.
> > > #
> > >
> >
> > =====================================
> > # To be removed from this list, send a message to
> > # discussion-request at nsrca.org
> > # and put leave discussion on the first line of the body.
> > #
> >
>
>
> =====================================
> # To be removed from this list, send a message to
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
>
>


=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#