Mintor 140 Bearings

[Dean Pappas]

If you don't know who the local Amsoil guy is, just try <amsoil.com>
The MP1 works great, and does not hinder the first start of the new day's flying at all, but do not put it in a YS!
Stan Rauktis at S&W fuel turned me onto the stuff in '87!
Dean P.

-----Original Message-----
From: rcaerobob at cox.net [mailto:rcaerobob at cox.net]
Sent: Monday, August 04, 2003 2:03 PM
To: discussion at nsrca.org
Subject: Re: Re: Mintor 140 Bearings


Any Amsoil distributor...I don't remember the one I used.  I think Tom Collins at BuyRC.com is an Amsoil distributor, but I may be mistaken.
  The stuff I got was in a spray can, looks a lot like a WD 40 can, but it is Amsoil "Metal Protectant Spray"...I think MP1 is the p/n.

Bob Pastorello

> 
> From: VicenteRC <vicenterc at comcast.net>
> Date: 2003/08/04 Mon PM 01:42:01 EDT
> To: discussion at nsrca.org
> Subject: Re: Mintor 140 Bearings
> 
> Bob:
> 
> Where you buy the Amsoil MP1.
> 
> Thanks,
> 
> Vicente Bortone
> 
> 
> 
> ----- Original Message -----
> From: rcaerobob at cox.net
> Date: Monday, August 4, 2003 11:18 am
> Subject: Re: Mintor 140 Bearings
> 
> > I'm sure both David Harmon (suggestion about 50-50% mix of 
> > methanol/castor oil as after run) and Tom Collins (BuyRC.com 
> > importer/distributor) will reply.
> >  I'm using the SS brg in my OS 1.60, and it is very clean after 
> > 50 flights.  I'm using spray Amsoil MP1 "metal protectant" on the 
> > advice of Dave Lockhart, and that's all in the OS.
> >  In the Mintor, I haven't yet run it, but WILL be using the 
> > Harmon 50-50 and Mintor-suggested procedure.  And SS bearings, if 
> > they are available.
> >  Just my .01 worth....
> > 
> > Bob Pastorello
> > > 
> > > From: VicenteRC <vicenterc at comcast.net>
> > > Date: 2003/08/04 Mon PM 12:02:31 EDT
> > > To: NSRCA <discussion at nsrca.org>
> > > Subject: Mintor 140 Bearings
> > > 
> > > 
> > > I have three questions.  
> > > 
> > > 1. - Is the Mintor 140 bearings same size of the OS 140RX bearings?
> > > 2. - The original bearings is these engines didn't last too 
> > long.  Yes, 
> > > I have both engines.  I estimated less than 50 flies each.  
> > Clearly, 
> > > corrosion was the problem.  I already installed a new SS bearing 
> > on the 
> > > OS 140 RX.  I have a spare bearing that I hope I can use in the 
> > Mintor 
> > > 140.  The second question is: What is the approximate life of 
> > the SS 
> > > bearings?  
> > > 3. - Does it make sense to install ceramic bearings to improve 
> > the life?
> > > 
> > > I switched this year to 2C and looks like I am doing something 
> > very 
> > > wrong.  I know that I am not following the Mintor instructions 
> > "run or 
> > > flush the engine with 0% nitro fuel is you don't use the engine 
> > for 
> > > more than one week"
> > > 
> > > Thanks in advance,
> > > 
> > > Vicente Bortone
> > > 
> > > 
> > > =====================================
> > > # To be removed from this list, send a message to 
> > > # discussion-request at nsrca.org
> > > # and put leave discussion on the first line of the body.
> > > #
> > > 
> > > 
> > 
> > Bob Pastorello, El Reno, OK, USA
> > rcaerobob at cox.net
> > www.rcaerobats.net
> > 
> > =====================================
> > # To be removed from this list, send a message to 
> > # discussion-request at nsrca.org
> > # and put leave discussion on the first line of the body.
> > #
> > 
> > 
> 
> =====================================
> # To be removed from this list, send a message to 
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
> 
> 

Bob Pastorello, El Reno, OK, USA
rcaerobob at cox.net
www.rcaerobats.net

=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#

==================# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#