Temptation

[Tomanek, Wojtek]

Lee the temptation looks way cool.  Are the cheek cowles functional to
provide cool air to the bearing area and to exhaust hot air from the engine
compartment??  Hope to see it flying at BARKS


Wojtek

 

	-----Original Message-----
	From:	Lee Davis [SMTP:lee at piedmontmodels.com]
	Sent:	Friday, September 20, 2002 8:31 AM
	To:	discussion at nsrca.org
	Subject:	Re: Webra nose ring

	I've used the ARI with YS nose ring, as is, on a couple of Webra
	installations, but it's been a while.  I think I might have flipped
the nose
	ring over, moving it a little further forward to a narrower part of
the
	taper.

	I'll check on this and get back.

	Lee Davis
	Piedmont Models
	http://www.piedmontmodels.com/

	----- Original Message -----
	From: "Jerry Budd" <jbudd at QNET.COM>
	To: <discussion at nsrca.org>
	Sent: Friday, September 20, 2002 4:15 AM
	Subject: Re: Webra nose ring


	> John,
	>
	> The nose ring that Merle uses on the ARI mount is made by Clayton
	> Foster.  Since the mount/nose ring you have is for a YS the fix to
	> make it work with a Webra is REAL easy.  Remove the stock O-ring.
Go
	> to your local auto parts store (I went to Pep Boys) and get a 3mm
	> wide x 32mm ID x 38mm OD metric O-ring and install it.  It's a
	> perfect fit in the nose ring housing and on the tapered front case
of
	> the Webra (the brand I purchased is Metric Tite #64632, ~$1.49 for
4).
	>
	> Jerry
	>
	>
	> >A tight fit is not the best situation.  You are transferring a
lot
	> >of vibration here that is best avoided.  It will also wear out.
Why
	> >not contact Bully, at losborn at hwy97.net and order a Bully/Webra
nose
	> >ring from him that fits.  $9
	> >
	> >--Lance
	> >
	> >
	> >John Crozier <sjcrozier at comcast.net>
	> >Sent by: discussion-request at nsrca.org
	> >
	> >09/19/2002 12:46 PM
	> >Please respond to discussion
	> >
	> >         To:        nsrca discussion <discussion at nsrca.org>
	> >         cc:
	> >         Subject:        Webra nose ring
	> >
	> >
	> >
	> >I have an ARI mount for the Webra/Focus. (learned shortly after
the
	purchase
	> >that the soft mount ain't necessary, but that's another story)
	> >Anyway,  the YS O ring in the nose ring/mount is too tight.
(Webra is
	> >tapered and this is a close as Merle can come)
	> >I have replaced the original O ring with 1/8 fuel tube.
	> >When installed on the Webra, the tubing compresses to about 1/16
and
	gives a
	> >tight, but usable fit.
	> >Any reason why this should not be feasible?
	> >Thanx...croz
	> >
	> >
	> >=====================================
	> ># To be removed from this list, send a message to
	> ># discussion-request at nsrca.org
	> ># and put leave discussion on the first line of the body.
	> >#
	>
	>
	> --
	> ___________
	> Jerry Budd
	> mailto:jbudd at qnet.com
	> =====================================
	> # To be removed from this list, send a message to
	> # discussion-request at nsrca.org
	> # and put leave discussion on the first line of the body.
	> #

	=====================================
	# To be removed from this list, send a message to 
	# discussion-request at nsrca.org
	# and put leave discussion on the first line of the body.
	#
=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#