Coupler clamps

[Verne Koester]

Eric,
If they'll do a real honest 1.25", that'll just do. The silicone I'm using
on the E.S. 7/8" i.d. pipe mikes out at 1.235" installed.

Thanks!

Verne


----- Original Message -----
From: "Henderson,Eric" <eric.henderson at gartner.com>
To: <discussion at nsrca.org>
Sent: Monday, September 09, 2002 2:23 PM
Subject: RE: Coupler clamps


> Verne,
>        they look like the .61 clips but I think that they are bigger. I am
> using them on my OS 1.60 Hatori Header and ES pipe with the cream colored
> coupler. Here are the actual sizes - _I just measured them) Relaxed id =
1",
> max id = 1.25". They are the same ones that came with my OS 1.40 pipe and
> header etc. Does this meet your need?
>
> Regards,
>
> Eric.
>
> -----Original Message-----
> From: Verne Koester [mailto:verne at twmi.rr.com]
> Sent: Monday, September 09, 2002 4:16 PM
> To: discussion at nsrca.org
> Subject: Re: Coupler clamps
>
>
> Hi Eric,
> Thanks, are these the same ones that come in a .60-size Hatori pipe? I
have
> some of those and they are just a skosh too small.
>
> Verne
> ----- Original Message -----
> From: "Henderson,Eric" <eric.henderson at gartner.com>
> To: <discussion at nsrca.org>
> Sent: Monday, September 09, 2002 6:26 AM
> Subject: RE: Coupler clamps
>
>
> > There is a packet of just the clamps  part number HAT114.
> >
> > You can get them at the Hellicoptem rplace in Philly. They sell large
> scale
> > planes as well - Looking for their URL as I type. They are at the WRAM
> show
> > every year - on the main stage.
> >
> > Eric.
> >
> > http://www.hhiheli.com/
> >
> > Call them - The web-site is not easy to use. They are in Coopersburg PA.
> >
> > E.
> >
> > -----Original Message-----
> > From: Verne Koester [mailto:verne at twmi.rr.com]
> > Sent: Sunday, September 08, 2002 9:31 PM
> > To: discussion at nsrca.org
> > Subject: Re: Coupler clamps
> >
> >
> > Thanks Tom. I'm sure the size I need is available. Just a matter of
> finding
> > them!
> >
> > Verne
> >
> >
> > ----- Original Message -----
> > From: "Koenig, Tom" <Tom.Koenig at actewagl.com.au>
> > To: <discussion at nsrca.org>
> > Sent: Sunday, September 08, 2002 7:18 PM
> > Subject: RE: Coupler clamps
> >
> >
> > > Verne,
> > > Just a suggestion. I actually had the same problem at one stage. I
found
> > > some in a genuine O.S silicone coupler packet. Had to buy the the
whole
> > lot
> > > even though I was only after the clamps, which I guess is fair
> > >
> > > Strange thing is...I've never seen them since, rare as hens teeth down
> > > here!! Maybe not so around your part of the planet.
> > >
> > > Tom
> > >
> > > > ----------
> > > > From: Verne Koester[SMTP:verne at twmi.rr.com]
> > > > Reply To: discussion at nsrca.org
> > > > Sent: Monday, 9 September 2002 5:41
> > > > To: pattern at rcmailinglists.com; NSRCA
> > > > Subject: Coupler clamps
> > > >
> > > > Anybody know where I can get the spring style coupler clamps that
will
> > fit
> > > > over a coupler with a 1.235 o.d.? The clamps I'm referring too are
the
> > > > type that comes with a hatori muffler. The tubing to fit over is
7/8"
> > > > i.d., 1.235 o.d..
> > > >
> > > > Thanks,
> > > > Verne
> > > >
> > > >
> > > >
> > >
> > >
> > >
************************************************************************
> > > *PLEASE NOTE*  This email and any attachments may
> > > be confidential. If received in error, please delete all
> > > copies and advise the sender. The reproduction or
> > > dissemination of this email or its attachments is
> > > prohibited without the consent of the sender.
> > >
> > > WARNING RE VIRUSES:  Our computer systems sweep
> > > outgoing email to guard against viruses, but no warranty
> > > is given that this email or its attachments are virus free.
> > > Before opening or using attachments, please check for
> > > viruses.  Our liability is limited to the re-supply of any
> > > affected attachments.
> > >
> > > Any views expressed in this message are those of the
> > > individual sender, except where the sender expressly,
> > > and with authority, states them to be the views of the
> > > organisation.
> > >
************************************************************************
> > >
> > >
> > > =====================================
> > > # To be removed from this list, send a message to
> > > # discussion-request at nsrca.org
> > > # and put leave discussion on the first line of the body.
> > > #
> > >
> > >
> >
> > =====================================
> > # To be removed from this list, send a message to
> > # discussion-request at nsrca.org
> > # and put leave discussion on the first line of the body.
> > #
> > =====================================
> > # To be removed from this list, send a message to
> > # discussion-request at nsrca.org
> > # and put leave discussion on the first line of the body.
> > #
> >
> >
>
> =====================================
> # To be removed from this list, send a message to
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
> =====================================
> # To be removed from this list, send a message to
> # discussion-request at nsrca.org
> # and put leave discussion on the first line of the body.
> #
>
>

=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#