2005 Masters

[Anthony Romano]

Eric,
I get it now! Sort of a diamond cuban eight. I was doing the maneuver 
vertically.

Anthony

>From: "Henderson,Eric" <eric.henderson at gartner.com>
>Reply-To: discussion at nsrca.org
>To: discussion at nsrca.org
>Subject: RE: 2005 Masters
>Date: Wed, 2 Oct 2002 08:51:47 -0400
>
>Anthony,
>	  A 1/4 loop is 90 degrees. A 1/8 loop is 45 degrees.
>
>A diamond 8 has one 1/8 loop, then two 1/4 loops, one inverted roll on the
>45 down line, then three 1/4 outside loops, one upright roll on the 45 down
>line and then 1/8 loop to pull out to level flight.
>
>Best idea would be to draw this and then count them.
>
>
>              /\  /\
>		/  \/  \
>             \  /\  /
>         >____\/  \/____>
>Eric.
>
>
>
>
>Anthony Romano wrote:
>
> > Hi Eric,
> > Two questions
> >
> > >Stall Turn 1 and 1/4 Rolls up, 3/4 Roll down, Exit Inverted
> > >Model pulls through one-quarter (1/4) loop to vertical flight,
> > >pauses, performs one-and-one-quarter (1-1/4) rolls,
> > >pauses, performs a 180 degree stall turn in the direction
> > >of the maneuver to a vertical dive, pauses, performs
> > >a three-quarter (3/4) roll in opposite rotation, pauses, then pushes
> > >through one-quarter (1/4) loop to recover in inverted level
> > >flight.
> > >Downgrades:
> > >1. Track not vertical at beginning and end of rolls
> > >and stall turn.
> > >2. Track of stall turn not 180 degrees.
> > >3. Over or under rotation of rolls. 1 Point per 15
> > >Degree Rule.
> > >4. Rolls not centered in vertical lines.
> > >5. Loop segments not round and of equal radius.
> > >6. Pendulum movement after stall.
> > >7. Exit not same altitude and heading as entry.
> > >8. Roll rates not constant.
> > >
> >
> > Sorry, I took my rule book out of my briefcase so I can't look this up 
>my
> > self. There was a question at the judging seminar earlier this year 
>about
> > less than 180 degrees of track when wind corrected. Has this been 
>resolved
> > or specified in another section?
> >
> > >>
> > >Inside-Outside Diamond Eight with 1/1, Full Rolls, on center 45's
> > >Model passes through center and pulls one eighth (1/8) loop to
> > >45 degree up line, draws another straight line then pulls quarter (1/4)
> > >loop, draws straight line and pulls one quarter loop (1/4). Model
>hesitates
> > >and performs one roll (1/1), hesitates and pushes one quarter loop 
>(1/4)
>to
> > >45 degree up line, draws line and then pushes one quarter loop (1/4),
>draws
> > >straight line, pushes one quarter loop (1/4), hesitates and performs 
>one
> > >roll (1/1), hesitates pulls one-eighth loop (1/8) to level flight.
> > >Downgrades.
> > >
> >
> > <<<<I think you need another pull quarter loop after the role or you 
>wind
>up
> > on
> > a verticle downline.>>>>
>
>I arrive at the same conclusion, Anthony.Georgie
>
> >
> >
> > Anthony
> >
> > _________________________________________________________________
> > MSN Photos is the easiest way to share and print your photos:
> > http://photos.msn.com/support/worldwide.aspx
> >
> > =====================================
> > # To be removed from this list, send a message to
> > # discussion-request at nsrca.org
> > # and put leave discussion on the first line of the body.
> > #
>
>
>
>=====================================
># To be removed from this list, send a message to
># discussion-request at nsrca.org
># and put leave discussion on the first line of the body.
>#
>=====================================
># To be removed from this list, send a message to
># discussion-request at nsrca.org
># and put leave discussion on the first line of the body.
>#




_________________________________________________________________
Join the world’s largest e-mail service with MSN Hotmail. 
http://www.hotmail.com

=====================================
# To be removed from this list, send a message to 
# discussion-request at nsrca.org
# and put leave discussion on the first line of the body.
#