<html><head></head><body><div style="color:#000; background-color:#fff; font-family:Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif;font-size:13px"><div id="yui_3_16_0_1_1490544840721_3108"><span id="yui_3_16_0_1_1490544840721_3107">Yes, set the geometry as symmetrical as possible for the two servos. Go into the limit menu(12fg) and use the travel adjustments to get identical throws.</span></div><div id="yui_3_16_0_1_1490544840721_3108" dir="ltr">I usually set the throws to be identical in the normal flying rate and let the snap rate end up where it may. If your real industrious and have extra servos you can try multiple servos and see which ones match up the best. But even then I think they change with use. Also be sure that the limit is set high enough that you don't bump up against it.</div><div id="yui_3_16_0_1_1490544840721_3108" dir="ltr"><br></div><div id="yui_3_16_0_1_1490544840721_3108" dir="ltr">It would be nice if programmable servos could be matched up at several points rather than just the endpoints.</div> <div class="qtdSeparateBR"><br><br></div><div class="yahoo_quoted" style="display: block;"> <div style="font-family: Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 13px;"> <div style="font-family: HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, sans-serif; font-size: 16px;"> <div dir="ltr"><font size="2" face="Arial"> On Sunday, March 26, 2017 12:46 AM, Jas S via NSRCA-discussion <nsrca-discussion@lists.nsrca.org> wrote:<br></font></div> <br><br> <div class="y_msg_container"><div id="yiv8731807233"><div><div>One thing I've found (and forgot while setting up my 3M Extra), is to match my aileron (and dual elevator) servos before installing them. Adjust the end points you want first (ATV/AFR) if needed, then match the servo arms so with the servos against each other you can set a ruler on top of the arms and bisect all the holes and servo arm screws without subtrimming. I forgot to do this in one wing and at some point have to redo it cause my numbers are all over the place. Then adjust the linkages to set the surface straight. This should get you super close without any adjustments. If they're off, I take the lazy way out and match throws in the rate I fly the most (high Ail, low elv). Not the solution you probably wanted but just another way to do it. </div><div id="yiv8731807233AppleMailSignature"><br clear="none">Jas iP</div><div class="yiv8731807233yqt4821743720" id="yiv8731807233yqt32263"><div><br clear="none">On Mar 25, 2017, at 10:44 PM, Larry Diamond via NSRCA-discussion <<a rel="nofollow" shape="rect" ymailto="mailto:nsrca-discussion@lists.nsrca.org" target="_blank" href="mailto:nsrca-discussion@lists.nsrca.org">nsrca-discussion@lists.nsrca.org</a>> wrote:<br clear="none"><br clear="none"></div><blockquote type="cite"><div></div></blockquote></div></div><div class="yiv8731807233yqt4821743720" id="yiv8731807233yqt28167"><style>#yiv8731807233 #yiv8731807233 --
_filtered #yiv8731807233 {font-family:Wingdings;panose-1:5 0 0 0 0 0 0 0 0 0;}
_filtered #yiv8731807233 {panose-1:2 4 5 3 5 4 6 3 2 4;}
_filtered #yiv8731807233 {font-family:Calibri;panose-1:2 15 5 2 2 2 4 3 2 4;}
#yiv8731807233
#yiv8731807233 p.yiv8731807233MsoNormal, #yiv8731807233 li.yiv8731807233MsoNormal, #yiv8731807233 div.yiv8731807233MsoNormal
{margin:0in;margin-bottom:.0001pt;font-size:11.0pt;}
#yiv8731807233 a:link, #yiv8731807233 span.yiv8731807233MsoHyperlink
{color:#0563C1;text-decoration:underline;}
#yiv8731807233 a:visited, #yiv8731807233 span.yiv8731807233MsoHyperlinkFollowed
{color:#954F72;text-decoration:underline;}
#yiv8731807233 p.yiv8731807233MsoListParagraph, #yiv8731807233 li.yiv8731807233MsoListParagraph, #yiv8731807233 div.yiv8731807233MsoListParagraph
{margin-top:0in;margin-right:0in;margin-bottom:0in;margin-left:.5in;margin-bottom:.0001pt;font-size:11.0pt;}
#yiv8731807233 span.yiv8731807233EmailStyle17
{color:windowtext;}
#yiv8731807233 .yiv8731807233MsoChpDefault
{}
_filtered #yiv8731807233 {margin:1.0in 1.0in 1.0in 1.0in;}
#yiv8731807233 div.yiv8731807233WordSection1
{}
#yiv8731807233
_filtered #yiv8731807233 {}
_filtered #yiv8731807233 {font-family:Wingdings;}
_filtered #yiv8731807233 {}
_filtered #yiv8731807233 {font-family:Wingdings;}
_filtered #yiv8731807233 {font-family:Symbol;}
_filtered #yiv8731807233 {}
_filtered #yiv8731807233 {font-family:Wingdings;}
_filtered #yiv8731807233 {font-family:Symbol;}
_filtered #yiv8731807233 {}
_filtered #yiv8731807233 {font-family:Wingdings;}
#yiv8731807233 ol
{margin-bottom:0in;}
#yiv8731807233 ul
{margin-bottom:0in;}
#yiv8731807233 </style><div><div class="yiv8731807233WordSection1"><div class="yiv8731807233MsoNormal">I need help programming a Futaba T14SG for a 62” Acuity… I plan to use the T14SG for my sport planes (non- 2M Pattern planes). First time using this Tx.</div><div class="yiv8731807233MsoNormal"> </div><div class="yiv8731807233MsoNormal">I set the Ailerons up mechanically as close as I can to match both sides and to center the servo arm with the control surface centered. I think mechanically I am good, but not perfect.</div><div class="yiv8731807233MsoNormal"> </div><div class="yiv8731807233MsoNormal">I set the endpoints for 20 degrees up/down on both ailerons. Double checked and they track together. No problems at this point</div><div class="yiv8731807233MsoNormal"> </div><div class="yiv8731807233MsoNormal">Dual Rates for #1</div><div class="yiv8731807233MsoListParagraph" style=""><span style="font-family:Wingdings;"><span style="">Ø<span style="font:7.0pt;"> </span></span></span>Set up right wing up/down 12 degrees.</div><div class="yiv8731807233MsoListParagraph" style=""><span style="font-family:Wingdings;"><span style="">Ø<span style="font:7.0pt;"> </span></span></span>In checking the left wing it is 10 up and 14 down.</div><div class="yiv8731807233MsoNormal"> </div><div class="yiv8731807233MsoNormal">For #2 position, I use 100 for up down and it tracks 20 degrees up and down on both sides as expected with my endpoints set.</div><div class="yiv8731807233MsoNormal"> </div><div class="yiv8731807233MsoNormal">Am I not able to set up dual rate throws for each Aileron independently to ensure the throws are matched? I haven’t found the answer in the manual yet and seems I’m not setting something up correctly.</div><div class="yiv8731807233MsoNormal"> </div><div class="yiv8731807233MsoNormal">I can use my 18SZ if I need to. I don’t recall having this issue when I set up my Shinden with the 18SZ.</div><div class="yiv8731807233MsoNormal"> </div><div class="yiv8731807233MsoNormal"><span style="font-size:10.0pt;">Larry Diamond</span><span style="font-size:12.0pt;"></span></div><div class="yiv8731807233MsoNormal"> </div></div><blockquote type="cite"><div><span>_______________________________________________</span><br clear="none"><span>NSRCA-discussion mailing list</span><br clear="none"><span><a rel="nofollow" shape="rect" ymailto="mailto:NSRCA-discussion@lists.nsrca.org" target="_blank" href="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</a></span><br clear="none"><span><a rel="nofollow" shape="rect" target="_blank" href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion">http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</a></span></div></blockquote></div></div></div><div class="yqt4821743720" id="yqt84544">_______________________________________________<br clear="none">NSRCA-discussion mailing list<br clear="none"><a shape="rect" ymailto="mailto:NSRCA-discussion@lists.nsrca.org" href="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</a><br clear="none"><a shape="rect" href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target="_blank">http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</a></div><br><br></div> </div> </div> </div></div></body></html>