<html><head><style type="text/css"><!-- DIV {margin:0px;} --></style></head><body><div style="font-family:arial, helvetica, sans-serif;font-size:12pt"><DIV>I'll look for that feature in the Jeti manual....thanks.<BR></DIV>
<DIV style="FONT-SIZE: 12pt; FONT-FAMILY: arial, helvetica, sans-serif"><BR>
<DIV style="FONT-SIZE: 12pt; FONT-FAMILY: times new roman, new york, times, serif"><FONT face=Tahoma size=2>
<HR SIZE=1>
<B><SPAN style="FONT-WEIGHT: bold">From:</SPAN></B> Chris <cjm767driver@hotmail.com><BR><B><SPAN style="FONT-WEIGHT: bold">To:</SPAN></B> General pattern discussion <nsrca-discussion@lists.nsrca.org><BR><B><SPAN style="FONT-WEIGHT: bold">Sent:</SPAN></B> Thu, June 9, 2011 5:05:11 PM<BR><B><SPAN style="FONT-WEIGHT: bold">Subject:</SPAN></B> Re: [NSRCA-discussion] E-deadstick, trouble-shooting.<BR></FONT><BR>A Castle Tech told me that we want to set the current limiting to "insensitive" to avoid any false cut outs caused my momentary voltage drops. Along with that, you should hard set the cell count via the min voltage to 30V for a 10S setup. This has worked for lots and lots of us for many years with the Castle controllers.<BR><BR>Chris<BR><BR>On 6/9/2011 10:57 AM, Vicente "Vince" Bortone wrote:
<BLOCKQUOTE type="cite">
<STYLE type=text/css>p {margin:0;}</STYLE>
<DIV style="FONT-SIZE: 12pt; COLOR: rgb(0,0,0); FONT-FAMILY: Arial">I don't recall how CC call it. There is a setting for current slope or ramp. If you have it too sensitive the controller could shot down when you power up the plane in long vertical maneuvers. I didn't follow all the e-mails but this happen to me one time with a CC controller. <SPAN><BR><BR>Vicente "Vince" Bortone<BR></SPAN><BR>----- Original Message -----<BR>From: "colin chariandy" <A class=moz-txt-link-rfc2396E href="mailto:cchariandy@yahoo.ca" target=_blank rel=nofollow ymailto="mailto:cchariandy@yahoo.ca"><cchariandy@yahoo.ca></A><BR>To: "General pattern discussion" <A class=moz-txt-link-rfc2396E href="mailto:nsrca-discussion@lists.nsrca.org" target=_blank rel=nofollow ymailto="mailto:nsrca-discussion@lists.nsrca.org"><nsrca-discussion@lists.nsrca.org></A><BR>Sent: Thursday, June 9, 2011 9:41:55 AM<BR>Subject: Re: [NSRCA-discussion] E-deadstick,
trouble-shooting.<BR><BR>
<DIV style="FONT-SIZE: 12pt; FONT-FAMILY: arial, helvetica, sans-serif">
<DIV>The losses(heat) is not only dependent on current (I2R) but also Mosfet switching losses. V(in) is a factor in the equations.</DIV>
<DIV> </DIV>
<DIV>Colin<BR></DIV>
<DIV style="FONT-SIZE: 12pt; FONT-FAMILY: arial, helvetica, sans-serif"><BR>
<DIV style="FONT-SIZE: 13px; FONT-FAMILY: arial, helvetica, sans-serif"><FONT face=Tahoma size=2>
<HR SIZE=1>
<B><SPAN style="FONT-WEIGHT: bold">From:</SPAN></B> Keith Hoard <A class=moz-txt-link-rfc2396E href="mailto:khoard@gmail.com" target=_blank rel=nofollow ymailto="mailto:khoard@gmail.com"><khoard@gmail.com></A><BR><B><SPAN style="FONT-WEIGHT: bold">To:</SPAN></B> General pattern discussion <A class=moz-txt-link-rfc2396E href="mailto:nsrca-discussion@lists.nsrca.org" target=_blank rel=nofollow ymailto="mailto:nsrca-discussion@lists.nsrca.org"><nsrca-discussion@lists.nsrca.org></A><BR><B><SPAN style="FONT-WEIGHT: bold">Sent:</SPAN></B> Thu, June 9, 2011 9:53:21 AM<BR><B><SPAN style="FONT-WEIGHT: bold">Subject:</SPAN></B> Re: [NSRCA-discussion] E-deadstick, trouble-shooting.<BR></FONT><BR>FWIW - I have the CC Ice HV 80 in an Integral, and the data logger<BR>typically shows the temp rising to around 140-150F (60-80 amp draw)<BR>and hovering there for the entire flight. Castle tech support says<BR>that their controllers don't start throttling
back the juice until the<BR>internal temp reaches over 200F.<BR><BR>What I find interesting is that I have the same controller on my<BR>Osiris (5S pack vs. 10S pack) pulling the same 80 amps, but the<BR>controller temp only rises to about 90F on the Osiris.<BR><BR>I haven't downloaded the data from Andersonville, but I didn't see any<BR>power loss all weekend. I'm sure that if the system was going to<BR>overtemp, it would have happened this last weekend.<BR><BR>Keith Hoard<BR>Collierville, TN<BR><A href="mailto:khoard@gmail.com" target=_blank rel=nofollow ymailto="mailto:khoard@gmail.com">khoard@gmail.com</A><BR><BR><BR><BR><BR><BR>On Thu, Jun 9, 2011 at 8:36 AM, colin chariandy <<A href="mailto:cchariandy@yahoo.ca" target=_blank rel=nofollow ymailto="mailto:cchariandy@yahoo.ca">cchariandy@yahoo.ca</A>> wrote:<BR>> Got it....I'll add a path for air around the controller.<BR>><BR>> Thanks<BR>> Colin.<BR>><BR>>
________________________________<BR>> From: Verne Koester <<A href="mailto:verne@twmi.rr.com" target=_blank rel=nofollow ymailto="mailto:verne@twmi.rr.com">verne@twmi.rr.com</A>><BR>> To: General pattern discussion <<A href="mailto:nsrca-discussion@lists.nsrca.org" target=_blank rel=nofollow ymailto="mailto:nsrca-discussion@lists.nsrca.org">nsrca-discussion@lists.nsrca.org</A>><BR>> Sent: Thu, June 9, 2011 9:32:20 AM<BR>> Subject: Re: [NSRCA-discussion] E-deadstick, trouble-shooting.<BR>><BR>> Yes. My controller is mounted immediately behind the motor and in front of<BR>> the batteries. Air coming in the chin cowl flows over the controller and<BR>> batteries and then goes back out the exit which is two, 7” X 1” exit holes<BR>> in the bottom of the fuse right behind the wing tube. I also have two small<BR>> openings in my cheek cowls that are hopefully feeding the fan in the motor.<BR>> Some of the air
from those is probably hitting the controller and batteries<BR>> as well.<BR>><BR>><BR>><BR>> Verne Koester<BR>><BR>><BR>><BR>> From: <A href="mailto:nsrca-discussion-bounces@lists.nsrca.org" target=_blank rel=nofollow ymailto="mailto:nsrca-discussion-bounces@lists.nsrca.org">nsrca-discussion-bounces@lists.nsrca.org</A><BR>> [mailto:<A href="mailto:nsrca-discussion-bounces@lists.nsrca.org" target=_blank rel=nofollow ymailto="mailto:nsrca-discussion-bounces@lists.nsrca.org">nsrca-discussion-bounces@lists.nsrca.org</A>] On Behalf Of colin<BR>> chariandy<BR>> Sent: Thursday, June 09, 2011 12:28 AM<BR>> To: General pattern discussion<BR>> Subject: Re: [NSRCA-discussion] E-deadstick, trouble-shooting.<BR>><BR>><BR>><BR>> Mississauga, Ontario.....beat a record high since the 50's.<BR>><BR>><BR>><BR>> Do you guys allow some air to flow from the chin, around the speed<BR>> controller area back
into the fuse?<BR>><BR>><BR>><BR>> Colin<BR>><BR>><BR>><BR>> ________________________________<BR>><BR>> From: Ron Van Putte <<A href="mailto:vanputte@cox.net" target=_blank rel=nofollow ymailto="mailto:vanputte@cox.net">vanputte@cox.net</A>><BR>> To: General pattern discussion <<A href="mailto:nsrca-discussion@lists.nsrca.org" target=_blank rel=nofollow ymailto="mailto:nsrca-discussion@lists.nsrca.org">nsrca-discussion@lists.nsrca.org</A>><BR>> Sent: Wed, June 8, 2011 11:43:00 PM<BR>> Subject: Re: [NSRCA-discussion] E-deadstick, trouble-shooting.<BR>><BR>> Wow! 34C converts to 93.2F. What part of Canada was this in?<BR>><BR>> I agree with Keith. I run my Jeti 90 on standoffs, using the three mounting<BR>> holes. Never had a problem, even at Andersonville, GA last weekend, where<BR>> the temperatures were in the upper 90sF.<BR>><BR>> Ron Van
Putte<BR>><BR>> On Jun 8, 2011, at 10:32 PM, Keith Hoard wrote:<BR>><BR>>> Sounds like ESC shut down for heat. Does the Jeti have data logging?<BR>>><BR>>><BR>>><BR>>> Keith Hoard<BR>>> Collierville, TN<BR>>><BR>>> On Jun 8, 2011, at 21:57, colin chariandy <<A href="mailto:cchariandy@yahoo.ca" target=_blank rel=nofollow ymailto="mailto:cchariandy@yahoo.ca">cchariandy@yahoo.ca</A>> wrote:<BR>>><BR>>>> Hey guys...I was out practicing tonight when the motor lost all power in<BR>>>> the first upline of the M. Landed the plane deadstick and could find nothing<BR>>>> diconnected so I thought the battery was somehow open circuit. Plugged in<BR>>>> another batt and the controller armed and ran the motor normally.<BR>>>> Re-installed the previous batt and again all was OK. I flew the plane on<BR>>>> the same battery the failure
occured with and there were no re-occurences<BR>>>> but I was way too uncomfortable to really concentrate.<BR>>>><BR>>>> It was 34C when I took off....the hottest I have ever flown that plane<BR>>>> and I did have the controller velcroed in place in the chin with foam under<BR>>>> it to prevent movement....not the coolest set-up.<BR>>>><BR>>>> The plane is a Xigris, motor is the 30-10 evo and a Jeti 90 speed<BR>>>> controller, JR Rx.<BR>>>><BR>>>> Any trouble shooting advice? Do the Jetis have a thermal shut down?<BR>>>><BR>>>> I did change the speed controller mounting to use the three screws<BR>>>> instead of velcro.<BR>>>><BR>>>> Colin<BR>>>><BR>>>><BR>>>><BR>>>><BR>>>> _______________________________________________<BR>>>> NSRCA-discussion mailing
list<BR>>>> <A href="mailto:NSRCA-discussion@lists.nsrca.org" target=_blank rel=nofollow ymailto="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</A><BR>>>> <A href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target=_blank rel=nofollow>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</A><BR>>> _______________________________________________<BR>>> NSRCA-discussion mailing list<BR>>> <A href="mailto:NSRCA-discussion@lists.nsrca.org" target=_blank rel=nofollow ymailto="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</A><BR>>> <A href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target=_blank rel=nofollow>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</A><BR>><BR>> _______________________________________________<BR>> NSRCA-discussion mailing list<BR>> <A href="mailto:NSRCA-discussion@lists.nsrca.org"
target=_blank rel=nofollow ymailto="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</A><BR>> <A href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target=_blank rel=nofollow>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</A><BR>><BR>> _______________________________________________<BR>> NSRCA-discussion mailing list<BR>> <A href="mailto:NSRCA-discussion@lists.nsrca.org" target=_blank rel=nofollow ymailto="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</A><BR>> <A href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target=_blank rel=nofollow>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</A><BR>><BR>_______________________________________________<BR>NSRCA-discussion mailing list<BR><A href="mailto:NSRCA-discussion@lists.nsrca.org" target=_blank rel=nofollow
ymailto="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</A><BR><A href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target=_blank rel=nofollow>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</A></DIV></DIV></DIV><BR>_______________________________________________<BR>NSRCA-discussion mailing list<BR><A class=moz-txt-link-abbreviated href="mailto:NSRCA-discussion@lists.nsrca.org" target=_blank rel=nofollow ymailto="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</A><BR><A class=moz-txt-link-freetext href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target=_blank rel=nofollow>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</A></DIV><PRE><FIELDSET class=mimeAttachmentHeader></FIELDSET>
_______________________________________________
NSRCA-discussion mailing list
<A class=moz-txt-link-abbreviated href="mailto:NSRCA-discussion@lists.nsrca.org" target=_blank rel=nofollow ymailto="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</A>
<A class=moz-txt-link-freetext href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target=_blank rel=nofollow>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</A></PRE></BLOCKQUOTE></DIV></DIV></div></body></html>