<html>
<head>
<style><!--
.hmmessage P
{
margin:0px;
padding:0px
}
body.hmmessage
{
font-size: 10pt;
font-family:Tahoma
}
--></style>
</head>
<body class='hmmessage'>
I shall verify my setup today with respect to the zero line Don references below, but currently, using the stab as zero, I have +.6 wing and -1.2 engine. I shall check my CG, but I do have a pull to belly on left and right knife edge meaning I am too tail heavy. Anthony, is your Brio the carbon reinforcement nose version or the fiberglass only nose version. I thought they had different CG locations. Unfortunately, flight verification won't come until April here in good old Michigan.<BR> <BR>
Mike Cohen<BR>
D4<BR>
<HR id=stopSpelling>
From: anthonyr105@hotmail.com<BR>To: nsrca-discussion@lists.nsrca.org<BR>Date: Sun, 2 Jan 2011 09:55:32 -0500<BR>Subject: Re: [NSRCA-discussion] Zero reference line on the Brio<BR><BR>
<META content="Microsoft SafeHTML" name=Generator>
<STYLE>
.ExternalClass .ecxhmmessage P
{padding:0px;}
.ExternalClass body.ecxhmmessage
{font-size:10pt;font-family:Tahoma;}
</STYLE>
Took my Brio out of moth balls this year and converted it to E-power. After alot of playing with set up and discussions with Brian wound up with the cg just under 7" from the LE and the wing at almost +.75° to a 0 stab. No mix and best flying plane I have ever owned. <BR> <BR>Anthony<BR> <BR>
<HR id=ecxstopSpelling>
From: AtwoodDon@aol.com<BR>Date: Sat, 1 Jan 2011 21:59:26 -0500<BR>To: nsrca-discussion@lists.nsrca.org<BR>Subject: Re: [NSRCA-discussion] Zero reference line on the Brio<BR><BR><FONT id=ecxrole_document face=Arial color=#000000 size=2>
<DIV>I went back and looked at my notes and the original instructions state the tail should be 1" above the work bench, not 3/4". the directions also say to set the wing 1/4 degree positive and the stab 1/4 degree negative.</DIV>
<DIV> </DIV>
<DIV>Don</DIV>
<DIV> </DIV>
<DIV>
<DIV>In a message dated 1/1/2011 3:51:11 P.M. Pacific Standard Time, AtwoodDon@aol.com writes:</DIV>
<BLOCKQUOTE style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: blue 2px solid"><FONT style="BACKGROUND-COLOR: transparent" face=Arial color=#000000 size=2><FONT face=Arial color=#000000 size=2>
<DIV>I believe with the belly resting on a level work surface, the bottom of the fuselage at the back/bottom of the fin is supposed to be 3/4" above the table. The fuse would then be at 'zero'.</DIV>
<DIV> </DIV>
<DIV>Don</DIV>
<DIV> </DIV>
<DIV>
<DIV>In a message dated 1/1/2011 7:14:43 A.M. Pacific Standard Time, precisionaero@hotmail.com writes:</DIV>
<BLOCKQUOTE style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: blue 2px solid"><FONT style="BACKGROUND-COLOR: transparent" face=Tahoma color=#000000 size=2>Happy New Year everyone. Anyone know what the 0-0 reference line is on the Brio? It's winter maintenance time and I am verifying current stab, wing, and thrust incidences on my planes!<BR> <BR>Mike Cohen<BR>D4<BR>=<BR><BR>_______________________________________________<BR>NSRCA-discussion mailing list<BR>NSRCA-discussion@lists.nsrca.org<BR>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</FONT></BLOCKQUOTE></DIV></FONT><BR><BR>_______________________________________________<BR>NSRCA-discussion mailing list<BR>NSRCA-discussion@lists.nsrca.org<BR>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</FONT></BLOCKQUOTE></DIV></FONT><BR>_______________________________________________ NSRCA-discussion mailing list NSRCA-discussion@lists.nsrca.org http://lists.nsrca.org/mailman/listinfo/nsrca-discussion <BR>_______________________________________________ NSRCA-discussion mailing list NSRCA-discussion@lists.nsrca.org http://lists.nsrca.org/mailman/listinfo/nsrca-discussion </body>
</html>