<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.6000.16735" name=GENERATOR></HEAD>
<BODY bgColor=#ffffff>
<DIV>Aside from using a purpose built servo that matches logic families with the
receiver, the only real solution is to insert a level translater in between;
basically a simple buffer that allows you to take a lower voltage ourput signal
from one logic family in the receiver and boost the signal level to work with a
servo that requires higher levels for safe operating margins. Personally,
I would not fly other servos without doing this, even if they seem to be working
fine. Jim Oddino's post used two very instructive words:
"ragged edge". </DIV>
<DIV> </DIV>
<DIV><FONT face=Arial size=2>Ed</FONT></DIV>
<BLOCKQUOTE
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=bob@toprudder.com href="mailto:bob@toprudder.com">Bob Richards</A>
</DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A
title=nsrca-discussion@lists.nsrca.org
href="mailto:nsrca-discussion@lists.nsrca.org">General pattern discussion</A>
</DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Friday, November 21, 2008 9:42
PM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> Re: [NSRCA-discussion] Futaba
R6014FS Receivers</DIV>
<DIV><BR></DIV>
<TABLE cellSpacing=0 cellPadding=0 border=0>
<TBODY>
<TR>
<TD vAlign=top>
<DIV>I think I read somewhere that the R608FS receiver uses the same
chipset and has the same problem.</DIV>
<DIV> </DIV>
<DIV>So far I have not had any problems with the servos that I use, but
I was not able to check the pulse width out of the higher
channels with my Hitec programmer. I have to wonder, however, exactly
what is the logic level for the various servos? Also, does the logic
level of the servo change with a different battery voltage? Does the
output level from the rx change with a different battery voltage?</DIV>
<DIV> </DIV>
<DIV>I guess this is a good reason to use some sort of output
conditioner (powerbox, etc) if mixing brands of receivers and
servos.<BR></DIV>
<DIV>Bob R.</DIV>
<DIV> </DIV>
<DIV><BR>--- On <B>Fri, 11/21/08, MKMSG <I><mkmsg@cox.net></I></B>
wrote:<BR></DIV>
<BLOCKQUOTE
style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: rgb(16,16,255) 2px solid">From:
MKMSG <mkmsg@cox.net><BR>Subject: [NSRCA-discussion] Futaba
R6014FS Receivers<BR>To: "NSRCA Discussion List"
<nsrca-discussion@lists.nsrca.org><BR>Date: Friday, November 21,
2008, 1:15 AM<BR><BR>
<DIV id=yiv1661051185>
<STYLE></STYLE>
<DIV><FONT face=Arial size=2>I was reading the FAQ section of the
Futaba website when a particular item caught my eye regarding the
R6014FS 2.4 receiver. The FAQ states that <FONT
face="Times New Roman" size=3>the use of non Futaba digital servos
with the R6014FS receiver may be problematic due to the 6014's lower
output voltage of 2.7 volts. Since I do occasionally mix and
match Futaba and JR servos and use the 8 channel 2.4 receiver, I
wondered if this issue was common to all Futaba 2.4 receivers.
Here's Futaba's answer: "The FAQ refers only to the R6014FS receiver,
this is the only one that has the lower voltage." Just thought
I'd pass this along in case someone experiences performance anomalies
with the 6014 receivers using other than Futaba
servos.</FONT></FONT></DIV>
<DIV><FONT face=Arial size=2><FONT face="Times New Roman"
size=3></FONT></FONT> </DIV>
<DIV><FONT face=Arial size=2><FONT face="Times New Roman" size=3><FONT
face=Arial size=2>Mike</FONT></FONT></FONT></DIV>
<DIV><FONT face=Arial size=2><FONT face="Times New Roman" size=3><FONT
face=Arial size=2>NSRCA 35</FONT></DIV>
<DIV><BR></DIV></FONT></FONT></DIV><PRE>_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion@lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</PRE></BLOCKQUOTE></TD></TR></TBODY></TABLE>
<P>
<HR>
<P></P>_______________________________________________<BR>NSRCA-discussion
mailing
list<BR>NSRCA-discussion@lists.nsrca.org<BR>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</BLOCKQUOTE></BODY></HTML>