<html><body>
<DIV>Ron,</DIV>
<DIV> </DIV>
<DIV>I believe that you need to send the radio to Tony for pots adjustment. If the radio is new send it back to Futaba.</DIV>
<DIV> </DIV>
<DIV class=signature id=signature>--<BR>Vicente "Vince" Bortone</DIV>
<DIV> </DIV>
<BLOCKQUOTE style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #1010ff 2px solid">-------------- Original message -------------- <BR>From: Ron Van Putte <vanputte@cox.net> <BR><BR>> OK. I caved and went with ailevator. I nulled out the aileron <BR>> inputs and everything works as it should, EXCEPT I'm still getting a <BR>> small neutral shift on both elevators (same direction) when moving <BR>> the elevator dual rate switch. <BR>> <BR>> Ron <BR>> <BR>> On May 5, 2008, at 3:20 PM, Tony wrote: <BR>> <BR>> > Ron: <BR>> > Why are you re-inventing the wheel? <BR>> > Use the Ailvator pre-set mix for dual elevator servos already built <BR>> > into the <BR>> > 9Z.. <BR>> > <BR>> > <BR>> > Tony Stillman, President <BR>> > Radio South, Inc. <BR>> > 139 Altama Connector, Box 322 <BR>> > Brunswick, GA 31525 <BR>> > 1-800-962-7802 <BR>> > www.radiosouthrc.com <BR>> >
<BR>&g
t; > -----Original Message----- <BR>> > From: nsrca-discussion-bounces@lists.nsrca.org <BR>> > [mailto:nsrca-discussion-bounces@lists.nsrca.org] On Behalf Of Ron <BR>> > Van Putte <BR>> > Sent: Monday, May 05, 2008 4:09 PM <BR>> > To: General pattern discussion <BR>> > Subject: [NSRCA-discussion] Embarrassing Programming Problem <BR>> > <BR>> > I'm setting up a new airplane on my Futaba 9ZAP transmitter and using <BR>> > channels 2 and 6 for servos on each elevator half. I have PMX set <BR>> > for channels 2 and 6, mixing channel 2 into channel 6 and everything <BR>> > works fine, except the servo on channel 6 only moves about 2/3 the <BR>> > throw of the servo on channel 2. I've tried everything I can think <BR>> > of to rectify the problem with no success. In addition, there's a <BR>> > small shift in neutral when going from high rate elevator to low rate. <BR>> > <BR>> > I st
arted
with an unused model in the menu, so I don't think there's <BR>> > any hidden programming lurking. <BR>> > <BR>> > Any ideas? I'll be very irritated to find there's a simple solution, <BR>> > but I'd also be very grateful to have the problem go away. <BR>> > <BR>> > Ron Van Putte <BR>> > _______________________________________________ <BR>> > NSRCA-discussion mailing list <BR>> > NSRCA-discussion@lists.nsrca.org <BR>> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion <BR>> > <BR>> > _______________________________________________ <BR>> > NSRCA-discussion mailing list <BR>> > NSRCA-discussion@lists.nsrca.org <BR>> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion <BR>> <BR>> _______________________________________________ <BR>> NSRCA-discussion mailing list <BR>> NSRCA-discussion@lists.nsrca.org <BR>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussio
n </BL
OCKQUOTE></body></html>