<html><head><style type="text/css"><!-- DIV {margin:0px;} --></style></head><body><div style="font-family:times new roman, new york, times, serif;font-size:12pt"><DIV></DIV>
<DIV>This reminds me of a workshop incident 29 years ago . . . . I was making a spacer out of 5/8" particle board to put an aftermarket aircleaner on my 1978 Chevy Monza. I decided to "fuelproof" the spacer, but wanted to get it done in a hurry, so I mixed up a batch of 5 minute epoxy and thinned it quite a bit with alcohol. I painted the mixture on the spacer and was waiting for it to cure, when all of a sudden an epoxy "snake" started growing out of the mixing cup. It made kind of a hissing, snapping sound, and grew to be about 8 inches long. I figured the epoxy heated up enough to "boil" the epoxy while it was still somewhat pliable. The result was an interesting honey colored rock hard piece of epoxy foam. The epoxy on the particle board cured fine.<BR> </DIV>Bob Kane<BR>getterflash@yahoo.com
<DIV style="FONT-SIZE: 12pt; FONT-FAMILY: times new roman, new york, times, serif"><BR><BR>
<DIV style="FONT-SIZE: 12pt; FONT-FAMILY: times new roman, new york, times, serif">----- Original Message ----<BR>From: "patterndude@tx.rr.com" <patterndude@tx.rr.com><BR>To: NSRCA Mailing List <nsrca-discussion@lists.nsrca.org><BR>Cc: "Atwood, Mark" <atwoodm@paragon-inc.com><BR>Sent: Tuesday, November 20, 2007 4:48:13 PM<BR>Subject: Re: [NSRCA-discussion] Epoxy Question<BR><BR>Mr Fowler is out saving the world through explosives, but as a foot soldier in the cause, here's my understanding (and experience):<BR>Alcohol and acetone both mix into the resin/hardener solution. This makes is harder for crosslinking to occur and it separates the epoxy molecules trapping the alcohol. THe resulting solid will be a bit rubbery because of the trapped alcohol. Acetone is a more powerful solvent than alchohol and is beter for cleaning and thinning, but is also better for making rubber. <BR> The answer to the original
question is really somewhat obvious. Alcohol is volatile and will evaporate from the surface of the liquid in your mixing cup. As the epoxy cures, it exotherms (heats up) and this will also increase the evaporation. However, not all will evaporate. Whatever doesn't will be bound into the final rubbery solid. THe amount left behind is a variable affected by the size of the cup, heat in the room, amount of epoxy mixed, speed of cure, etc.<BR> The one time alcohol is OK to leave in the mix is when glassing. The very thin layer allows virtually all the alcohol to evaporate.<BR><BR>Also, Mike says he is using 91% alcohol. That means 9% water. Water is never good. He should go to home depot and buy a gallon of Denatured Alcohol. This is pretty close to 100% pure and it is less than half the price.<BR><BR>--Lance<BR><BR>---- "Atwood wrote: <BR><BR>=============<BR>Actually...my thought goes the
other direction. That if indeed the<BR>alcohol actually MIXES with the epoxy, then it would truly bind and in<BR>some way harden as part of the overall mixture. Epoxy "cures"...rather<BR>than flashing, so my guess...and it's truly a guess...is that it would<BR>be much closer to the original total weight of 2 oz. <BR><BR><BR><BR>Still waiting patiently for our resident epoxy deity, previously<BR>referred to as Master Fowler to take away the mystery and lead us oh so<BR>graciously to the light...<BR><BR><BR><BR>From: <A href="mailto:nsrca-discussion-bounces@lists.nsrca.org" ymailto="mailto:nsrca-discussion-bounces@lists.nsrca.org">nsrca-discussion-bounces@lists.nsrca.org</A><BR>[mailto:<A href="mailto:nsrca-discussion-bounces@lists.nsrca.org" ymailto="mailto:nsrca-discussion-bounces@lists.nsrca.org">nsrca-discussion-bounces@lists.nsrca.org</A>] On Behalf Of wgalligan<BR>Sent: Tuesday, November 20, 2007 9:52 AM<BR>To: Don Ramsey; NSRCA
Mailing List<BR>Subject: Re: [NSRCA-discussion] Epoxy Question<BR><BR><BR><BR>OK, I'll take a stab. After the alcohol evaporates you would have the<BR>same mass or weight of epoxy that you started with. AND to reiterate<BR>what I learned from the Master Fowler, thinning epoxy, if I remember<BR>right, changes the molecular structure weakening the mixture. It will<BR>also cause the epoxy to shrink over time. BTDT.<BR><BR><BR><BR>Wayne Galligan<BR><BR><BR><BR>waiting for Master to speak<BR><BR> ----- Original Message ----- <BR><BR> From: Don Ramsey <mailto:<A href="mailto:don.ramsey@suddenlink.net" ymailto="mailto:don.ramsey@suddenlink.net">don.ramsey@suddenlink.net</A>> <BR><BR> To: NSRCA Mailing List <mailto:<A href="mailto:nsrca-discussion@lists.nsrca.org"
ymailto="mailto:nsrca-discussion@lists.nsrca.org">nsrca-discussion@lists.nsrca.org</A>><BR><BR><BR> Sent: Tuesday, November 20, 2007 8:53 AM<BR><BR> Subject: [NSRCA-discussion] Epoxy Question<BR><BR> <BR><BR> Breaking news. Here's something from Mike Harrison that will be<BR>of interest to the list.<BR><BR> Don<BR><BR> <BR><BR> <BR><BR> Ok, think about this, take 1 oz epoxy and thin with 1 oz alcohol<BR>(91%).? After curing how much do you think it weighs and tell me why.<BR><BR> <BR><BR> Mike<BR><BR>________________________________<BR><BR> _______________________________________________<BR> NSRCA-discussion mailing list<BR> <A href="mailto:NSRCA-discussion@lists.nsrca.org"
ymailto="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</A><BR> <A href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target=_blank>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</A><BR><BR><BR>_______________________________________________<BR>NSRCA-discussion mailing list<BR><A href="mailto:NSRCA-discussion@lists.nsrca.org" ymailto="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</A><BR><A href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target=_blank>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</A><BR></DIV><BR></DIV></div><br>
<hr size=1>Be a better pen pal.
Text or chat with friends inside Yahoo! Mail. <a href="http://us.rd.yahoo.com/evt=51732/*http://overview.mail.yahoo.com/">See how.</a></body></html>