<HTML><BODY style="word-wrap: break-word; -khtml-nbsp-mode: space; -khtml-line-break: after-white-space; ">I know you ordered JR arms for JR servos, but be careful that you don't mistake "tight" with "too tight". I made the mistake of trying to use a Futaba servo arm on a Hitec 5625MG digital elevator servo. The arm seemed to fit fine because it was "tight" on the servo. A couple of flights later, I discovered dramatic elevator trim changes. The Futaba servo arm was slipping on the Hitec servo's output shaft. Wasn't fun.<DIV><BR class="khtml-block-placeholder"></DIV><DIV>Ron Van Putte</DIV><DIV><BR><DIV><DIV>On Aug 30, 2007, at 8:36 AM, k6xyz wrote:</DIV><BR class="Apple-interchange-newline"><BLOCKQUOTE type="cite"> <DIV class="Section1"><P class="MsoNormal"><FONT size="2" color="blue" face="Comic Sans MS"><SPAN style="font-size:10.0pt;font-family:" comic="" sans="" ms";color:blue"="">I had the same trouble with these arms.</SPAN></FONT></P><P class="MsoNormal"><FONT size="2" color="blue" face="Comic Sans MS"><SPAN style="font-size:10.0pt;font-family:" comic="" sans="" ms";color:blue"="">It seems that the spline in the arm is the right size, but it has debris or something in there…anyway, I was able to pick out some of the loose ‘stuff’ in the spline and it went on easier but I think it is still too tight.</SPAN></FONT></P><DIV><FONT size="2" color="blue" face="Comic Sans MS"><SPAN style="font-size:10.0pt;font-family:" comic="" sans="" ms";color:blue"=""> </SPAN></FONT><BR class="khtml-block-placeholder"></DIV> <DIV><P><FONT size="2" color="blue" face="Times New Roman"><SPAN style="font-size:10.0pt; color:blue">Regards<BR> <BR> Dave Harmon<BR> NSRCA 586<BR> K6XYZ[at]sbcglobal[dot]net<BR> Sperry, Ok.</SPAN></FONT><FONT color="blue"><SPAN style="color:blue"> </SPAN></FONT></P> </DIV><P class="MsoNormal" style="margin-left:.5in"><FONT size="2" face="Tahoma"><SPAN style="font-size:10.0pt;font-family:Tahoma">-----Original Message-----<BR> <B><SPAN style="font-weight:bold">From:</SPAN></B> nsrca-discussion-bounces@lists.nsrca.org [<A href="mailto:nsrca-discussion-bounces@lists.nsrca.org">mailto:nsrca-discussion-bounces@lists.nsrca.org</A>] <B><SPAN style="font-weight: bold">On Behalf Of </SPAN></B>twtaylor<BR> <B><SPAN style="font-weight:bold">Sent:</SPAN></B> Thursday, August 30, 2007 7:50 AM<BR> <B><SPAN style="font-weight:bold">To:</SPAN></B> <A href="mailto:nsrca-discussion@lists.nsrca.org">nsrca-discussion@lists.nsrca.org</A><BR> <B><SPAN style="font-weight:bold">Subject:</SPAN></B> [NSRCA-discussion] Metal Servo Arms</SPAN></FONT></P><DIV style="margin-left: 0.5in; "><FONT size="3" face="Times New Roman"><SPAN style="font-size:12.0pt"> </SPAN></FONT><BR class="khtml-block-placeholder"></DIV><P class="MsoNormal" style="margin-left:.5in"><FONT size="2" face="Arial"><SPAN style="font-size:10.0pt;font-family:Arial">I bought some Hanger 9 alum servo arms and when I put them on they are VERY hard to get to pull down on to the servo. Is this normal? They don’t go down as far as the plastic arms do. They are stamped with a J on the bottom so I assume they’re made for JR servo’s.</SPAN></FONT></P><DIV style="margin-left: 0.5in; "><FONT size="2" face="Arial"><SPAN style="font-size:10.0pt;font-family:Arial"> </SPAN></FONT><BR class="khtml-block-placeholder"></DIV><P class="MsoNormal" style="margin-left:.5in"><FONT size="2" face="Arial"><SPAN style="font-size:10.0pt;font-family:Arial">Tim</SPAN></FONT></P> </DIV><DIV style="margin-top: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; ">_______________________________________________</DIV><DIV style="margin-top: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; ">NSRCA-discussion mailing list</DIV><DIV style="margin-top: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; "><A href="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</A></DIV><DIV style="margin-top: 0px; margin-right: 0px; margin-bottom: 0px; margin-left: 0px; "><A href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion">http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</A></DIV> </BLOCKQUOTE></DIV><BR></DIV></BODY></HTML>