<HTML>
<HEAD>
<TITLE>Re: [NSRCA-discussion] SPEKTRUM modules for JR transmitters</TITLE>
</HEAD>
<BODY>
<FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'>On 6/10/07 8:14 AM, "JonLowe@aol.com" <JonLowe@aol.com> wrote:<BR>
<BR>
</SPAN></FONT><BLOCKQUOTE><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'>In a message dated 6/9/2007 9:53:50 AM Central Daylight Time, rbearden56@bellsouth.net writes:<BR>
</SPAN></FONT><BLOCKQUOTE><SPAN STYLE='font-size:12.0px'><FONT FACE="Arial">You must be very careful when dealing with these connectors they cannot be<BR>
over tightened without damaging the connector and severely degrading the<BR>
transmitters output. When you are dealing with the Gigahertz range most<BR>
connections are N-type OR SMA and you only need to torque then to ABOUT<BR>
6inch/oz (FINGER TIGHT). If you over tighten them you will damage it and<BR>
then your output will drop due to reflected energy back into the transmitter<BR>
module. If you treat it like the old stuff it get bad quickly. Don't<BR>
superglue it there is a compound to prevent the connectors from coming loose<BR>
that will not ruin it like super glue.<BR>
</FONT></SPAN></BLOCKQUOTE><SPAN STYLE='font-size:12.0px'><FONT FACE="Verdana, Helvetica, Arial">Randy,<BR>
You misunderstood what retaining nut I am talking about. It is NOT a nut that completes part of the RF circuit. It is a nut that retains the body of the connector in the SPEKTRUM housing, just like the nut that retains an RJ-6 connector in the back of a cable box or a TV. If it comes loose far enough, it can allow the whole connector body to rotate, pulling loose the connection on the circuit board. It is the flat nut shown at the bottom right of the picture below that retains the connector to the plastic housing.<BR>
<BR>
Jon Lowe<BR>
<IMG src="cid:3264350438_172929222" ><BR>
<BR>
<BR>
<BR>
<BR>
<HR ALIGN=CENTER SIZE="3" WIDTH="100%">See what's free at AOL.com <a href="http://www.aol.com?ncid=AOLAOF00020000000503"><http://www.aol.com?ncid=AOLAOF00020000000503></a> . <BR>
<BR>
<HR ALIGN=CENTER SIZE="3" WIDTH="95%"></FONT></SPAN><FONT SIZE="1"><FONT FACE="Monaco, Courier New"><SPAN STYLE='font-size:9.0px'>_______________________________________________<BR>
NSRCA-discussion mailing list<BR>
NSRCA-discussion@lists.nsrca.org<BR>
<a href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion">http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</a><BR>
</SPAN></FONT></FONT></BLOCKQUOTE><FONT SIZE="1"><FONT FACE="Monaco, Courier New"><SPAN STYLE='font-size:9.0px'><BR>
</SPAN></FONT></FONT><FONT FACE="Verdana, Helvetica, Arial"><SPAN STYLE='font-size:12.0px'>Jon,<BR>
<BR>
OK now I see what you are talking about. Does the connector have a flat spot to prevent the connector from turning when the female connector is attached? I agree that if this is not secure then the internal connection could be broken or frayed. Now if you want to have the advantages of 2.4 GHz and the programming of an advanced 12 channel transmitter then you should dump the JR conversion and go with the FUTABA pure bred (LOL). If you use super glue, then what happens if you need to remove the connection for service or changing a cracked plastic case, like when you slam the JR on the ground in frustration (LOL)? Try some tread lock instead, so when your hands are shaking it won’t let the nuts and bolts come loose. (More LOL)<BR>
<BR>
Good Luck at the NATS Jon, <BR>
<BR>
Randy</SPAN></FONT>
</BODY>
</HTML>