<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=iso-8859-1">
<META content="MSHTML 6.00.2900.2802" name=GENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY bgColor=#ffffff>
<DIV><FONT face=Arial size=2>Paul:</FONT></DIV>
<DIV><FONT face=Arial size=2>The soldering trick works fine, as long as you
don't get a cold joint. I try to avoid it only because the area near where
the solder stops wicking into the wire tends to be a point of stress
concentration for the wire strands, but as long as you extend the heat shrink
about 1/4" past the point where the wire gets 'bendy' again, it supports it and
prevents the work hardening of the wire from becoming a problem. I might
be a bit nervous about those servos though - how do the gears look? I've
had incidents where just a tiny sliver of a gear tooth was chipped away and lead
to further problems.</FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>Ed</FONT></DIV>
<BLOCKQUOTE
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=paul.horan@sbcglobal.net
href="mailto:paul.horan@sbcglobal.net">paul</A> </DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A
title=nsrca-discussion@lists.nsrca.org
href="mailto:nsrca-discussion@lists.nsrca.org">NSRCA Mailing List</A> </DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Monday, March 13, 2006 10:29
PM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> Re: [NSRCA-discussion] Help:
Servo pins pulled out of connector body</DIV>
<DIV><BR></DIV>
<DIV><FONT face=Arial size=2>Ed,</FONT></DIV>
<DIV><FONT face=Arial size=2> Sounds like I can either get
the kit and crimper from Maxx or cut the connector ends off defunct servos /
extentions and solder them to the existing servo wires - using heat shrink to
keep any flexing away from the solder joints. Any preference
?</FONT></DIV>
<DIV><FONT face=Arial size=2>Thanks,</FONT></DIV>
<DIV><FONT face=Arial size=2>Paul</FONT></DIV>
<BLOCKQUOTE
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV style="FONT: 10pt arial">----- Original Message ----- </DIV>
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=ed_alt@hotmail.com href="mailto:ed_alt@hotmail.com">Ed Alt</A>
</DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A
title=nsrca-discussion@lists.nsrca.org
href="mailto:nsrca-discussion@lists.nsrca.org">NSRCA Mailing List</A> </DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Monday, March 13, 2006 9:24
PM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> Re: [NSRCA-discussion] Help:
Servo pins pulled out of connector body</DIV>
<DIV><BR></DIV>
<DIV><FONT face=Arial size=2>Paul:</FONT></DIV>
<DIV><FONT face=Arial size=2>Better off to replace the entire connector and
pins. Most likely the plastic housing was damaged from the pin pulling
out. Also, the wire had to get strained where it is clasped by the
crimp pins. Maxx Products sells connector kits, but you need a crimper
tool. </FONT></DIV>
<DIV><FONT face=Arial size=2></FONT> </DIV>
<DIV><FONT face=Arial size=2>Ed</FONT></DIV>
<DIV> </DIV>
<DIV>----- Original Message ----- </DIV>
<BLOCKQUOTE
style="PADDING-RIGHT: 0px; PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #000000 2px solid; MARGIN-RIGHT: 0px">
<DIV
style="BACKGROUND: #e4e4e4; FONT: 10pt arial; font-color: black"><B>From:</B>
<A title=paul.horan@sbcglobal.net
href="mailto:paul.horan@sbcglobal.net">paul</A> </DIV>
<DIV style="FONT: 10pt arial"><B>To:</B> <A
title=nsrca-discussion@lists.nsrca.org
href="mailto:nsrca-discussion@lists.nsrca.org">NSRCA Mailing List</A>
</DIV>
<DIV style="FONT: 10pt arial"><B>Sent:</B> Monday, March 13, 2006 10:13
PM</DIV>
<DIV style="FONT: 10pt arial"><B>Subject:</B> [NSRCA-discussion] Help:
Servo pins pulled out of connector body</DIV>
<DIV><BR></DIV>
<DIV><FONT face=Arial size=2> I strained my Meridian
through a tree, wrecked the plane but the equipment appears OK with the
exception of both aileron servos. When the wings came off the servo
connector body stayed in the fuse and the servos wires and pins went with
the wings. </FONT></DIV>
<DIV><FONT face=Arial size=2> My question is : can I
simply re-insert the servo pins in another connector body (taken from
defuct servos or extentions) ?</FONT></DIV>
<DIV><FONT face=Arial size=2>Thanks,</FONT></DIV>
<DIV><FONT face=Arial size=2>Paul</FONT></DIV>
<P>
<HR>
<P></P>_______________________________________________<BR>NSRCA-discussion
mailing
list<BR>NSRCA-discussion@lists.nsrca.org<BR>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</BLOCKQUOTE>
<P>
<HR>
<P></P>_______________________________________________<BR>NSRCA-discussion
mailing
list<BR>NSRCA-discussion@lists.nsrca.org<BR>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</BLOCKQUOTE>
<P>
<HR>
<P></P>_______________________________________________<BR>NSRCA-discussion
mailing
list<BR>NSRCA-discussion@lists.nsrca.org<BR>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</BLOCKQUOTE></BODY></HTML>