[NSRCA-discussion] Flight Coach Hardware

[Matthew Finley]

Good Morning Sir ! I am very interested in this Proton Pathfinder Unit. I looked on Ebay, but did not have any luck locating ? Would you happen to have a link to where I can purchase ?

Respectfully,

Matthew E. Finley
(614) 557-3846
________________________________
From: NSRCA-discussion <nsrca-discussion-bounces at lists.nsrca.org> on behalf of Bob Kane via NSRCA-discussion <nsrca-discussion at lists.nsrca.org>
Sent: Monday, August 15, 2022 9:25 AM
To: Andrew Palmer <f3akiwi at gmail.com>; General pattern discussion <nsrca-discussion at lists.nsrca.org>; Vicente Bortone <vincebrc at gmail.com>
Subject: Re: [NSRCA-discussion] Flight Coach Hardware

The Proton Pathfinder that you can get on Ebay is a nicely finished unit and includes everything listed below except the micro SD card. There should be a picture attached.



Bob Kane getterflash at yahoo.com


On Monday, August 15, 2022 at 08:42:06 AM EDT, Vicente Bortone via NSRCA-discussion <nsrca-discussion at lists.nsrca.org> wrote:


Thanks Andrew.  I will try to follow your instructions and advise.

Vicente “Vince” Bortone

On Sun, Aug 14, 2022 at 6:17 PM Andrew Palmer via NSRCA-discussion <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>> wrote:
Getting the Flight Coach system up and running can be a bit daunting - especially if you are not familiar with the use of flight control boards.

Having said that, if you spend a bit of time doing some reading, it is not so bad.....Flight Coach compatible log files can be produced by any flight control board which can run Ardupilot firmware. Ardupilot (specifically ArduPlane - the plane version of the firmware) is able to write log files that contain a nice fusion of GPS and accelerometer data that Flight Coach uses to create the ribbon plots.

In broad terms you need:
1. Ardupilot compatible flight control board
2. SD logger (most simple is if it is built into the flight control board)
3. GPS and Compass - again, most simple is if these are included in the same unit
4. Power supply (simplest is if the flight control board is compatible with direct 2s LiPo/LiFe voltage)
5. Micro SD card

You will need a computer to install the ArduPlane firmware, and do the required configuration steps.

You can use any combination of hardware you wish - so long as it is Ardupilot compatible. So the Ardupilot website is a great place to do research on hardware.

You will need to load the ArduPlane firmware on the flight control board.... again, this is covered on the Ardupilot website.

You then need to wire everything up and do a couple of calibrations - again, the Ardupilot website is of help here.

Finally, you need to set some parameters to enable the correct log file to be produced - the Flight Coach website has info on this.

With the current chip shortages, finding hardware is not so straight forward! There are a few ideas on the Flight Coach website, but of course many other possibilities. We have found the logs are of equal quality regardless of your hardware choices - so cheap stuff is fine!

BTW, at Flight Coach we don’t sell anything. And we have made all the code available to everyone. We hope this system can be used by all. We have previously (and may again) ask for donations to help cover the website costs - but that is it 😊

Andrew Palmer, NZ
Flight Coach
F3A Zone Pro



_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<mailto:NSRCA-discussion at lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
--
Vicente "Vince" Bortone
NSRCA 1140.  Be Proud to show your NSRCA #
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<mailto:NSRCA-discussion at lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20220815/3900be23/attachment.html>