[NSRCA-discussion] Price for a pattern plane...

[Curt Oberg]

Question for  you Jason.  Do you believe that the price of your equipment has an effect on the scores that you receive from the judges?  I have a feeling that if you have a $2000 contra setup in your plane instead of a HiMax motor, and the judge is thinking a maneuver is worth a 9 or a 9.5, you might get the 9.5 with the contra drive  and not the HiMax motor.  I believe that that the average pattern flyer, (that would not be you) is perhaps not considered to be a serious pattern flyer if all his gear is in the lower price range.  I believe it's just human nature, sort of.  I hope not but you have to wonder.  I've seen you fly the Acuity and it was poetry in motion.
Curt Oberg

-----Original Message-----
From: NSRCA-discussion [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Jas S via NSRCA-discussion
Sent: Sunday, December 30, 2018 7:15 PM
To: nsrca-discussion at lists.nsrca.org
Subject: [NSRCA-discussion] Price for a pattern plane...

There’s always been talk about how expensive pattern is. All disciplines and hobbies are expensive, it’s just a choice one makes as to how much they want to spend. I’ve not had a ‘top of the line $$$$’ model since I was a teen when I wasn’t paying for my planes. Back then I was lucky enough to get the best planes on the market. Ten Plus planes back then were as good as the Yang/Oxai planes of today, and relative cost was about the same. Since being on my own, I’ve had more average planes, price point at least. Sponsorship allows me to outfit my planes with what I consider some of the best equipment, but even then I don’t bling out my planes at every turn.

Example, Acuity set-up from the 2017 Nats in Blytheville, AR:
Plane: AJ Acuity $949
Motor: AJ 5230-20P $260
OS/Futaba ESC: $300 I think
Battery: ThunderPower 6000’s $220
Servos: Futaba SBUS, 173’s, 171’s & 175 $950 now 🤭
Receiver: Futaba 7006 $100 now
Falcon Spinner and Prop: $160 
Total works out to about: $2939

Most hardware is stock from the kit. Linkages, tail wheel assembly, sticky velcro hook side, axles, wheels. I changed the cowl screws, motor mounting screws (shorter) and velcro strap for the battery.

I could have used, and not hurt my performance any, this equipment:
Futaba 9650’s, 9151’s & 9155 ($430) and saved -$520
Futaba 617 receiver ($94) and saved -$6
Castle 80a ESC ($145) and saved -$155
Gator spinner ($18) and saved -$42
APC prop ($44) and saved -$56
Power Unlimited 5800’s ($186) and saved $34
Shulman Aviation 6v regulator ($20) +$20
Total saved: $658

So my Acuity set-up could be done for just about $2144. This is assuming you have NONE of the stuff to put in a 2m sized plane.

Now my Epic set-up from the 2018 Muncie, IN Nats is a different price point:
CA Model Epic $2780 (Evo price, I think Epic + was less)
Brenner Contra: $1000 last year
Kontronic Motor: $500
Add $100 for a 2nd Falcon prop
Subtract $60 for the Falcon spinner
Futaba servos/receiver, ThunderPower batteries and OS/Futaba ESC are the same prices as Acuity. 

I usually use 2mm carbon rod for pushrods, Du-Bro/Central Hobbies/F3AU links, MPI 2.25 wheels.

Total around $6000

Again, using equipment that’s not ‘top of the line’, I can save about $2400. Most of the difference from the Acuity savings is swapping the contra for a Himax set-up.

And the Yang/Oxai you can add another $~2500 to the total for a top-shelf set-up.

All this being said, the BEST deals for a newbie to pattern are:
Any sport/pattern capable plane they are comfortable flying.
Any second hand pattern plane they can afford.
A good friend with a spare plane they will loan you 😁

Have a safe Happy New Year to everyone and always land wheels down 😉

Jason
Jas iP
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion