[NSRCA-discussion] Castle settings

[Scott]

Glad you showed up to speak for yourself!

Sent from XFINITY Connect Mobile App



------ Original Message ------

From: Atwood, Mark
To: S. McNickle, General pattern discussion
Cc: Olstinske Dale, DaveL322
Sent: November 1, 2017 at 7:47 PM
Subject: Re: [NSRCA-discussion] Castle settings

Hey Scott,

Close... my issue was with a Hacker Q-80.Not the pletty.I’ve run the pletty on the Castle without a problem.

Greetings from chilly Argentina!

On Nov 1, 2017, at 8:08 PM, S. McNickle via NSRCA-discussion<nsrca-discussion at lists.nsrca.org(mailto:nsrca-discussion at lists.nsrca.org)>wrote:

>  
> Maybe I should let Mark Atwood speak for himself, but he's kinda busy right now...
>  
>  
> Mark told me he tried everything he could think of and couldn't get a Pletty Advance to run full power on a Castle ESC. He recommended the Jetti or O.S.I got the O.S. and it works fine.
>  
>  
>  
>  
>  
>  
> Scott
>  
> > On November 1, 2017 at 5:51 PM Olstinske Dale via NSRCA-discussion<nsrca-discussion at lists.nsrca.org(mailto:nsrca-discussion at lists.nsrca.org)>wrote:
> >  
> > V4.22, Low timing but is set on Outrunner Mode not 8khz…could that be it?Not sure why but thought I had read that the Advance works best in this mode?
> > Will check if that fixes it as soon as I can.
> > Dale
> >  
> >  
> >  
> > > On Nov 1, 2017, at 1:35 PM, DaveL322<DaveL322 at comcast.net(mailto:DaveL322 at comcast.net)>wrote:
> > > What are the other settings?
> > >  
> > > Specifically check -
> > > Software is 4.22, or higher
> > > Low timing
> > > 8khz pwm
> > >  
> > > And.... All solder joints and connectors are healthy.
> > >  
> > > Possibly try reloading software...not likely to help, but it might.
> > >  
> > > Regards,
> > >  
> > > Dave
> > >  
> > > Sent from my Sprint Samsung Galaxy Note5.
> > >  
> > > -------- Original message --------
> > > From: Olstinske Dale via NSRCA-discussion<nsrca-discussion at lists.nsrca.org(mailto:nsrca-discussion at lists.nsrca.org)>
> > > Date: 11/1/17 3:59 PM (GMT-05:00)
> > > To: General pattern discussion<nsrca-discussion at lists.nsrca.org(mailto:nsrca-discussion at lists.nsrca.org)>
> > > Subject: [NSRCA-discussion] Castle settings
> > >  
> > > I have an Edge 80 HV Esc, Plettenberg Advance motor. I usually need around 70-75 A to get good performance, but I can’t get more than 60A from this one. I’ve recalibrate the throttle (fixed end points) but no improvement. Wondering if there is some other setting causing this?
> > >  
> > > Thanks,
> > >  
> > > Dale
> > >  
> > >  
> > > _______________________________________________
> > > NSRCA-discussion mailing list
> > > NSRCA-discussion at lists.nsrca.org(mailto:NSRCA-discussion at lists.nsrca.org)
> > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>  
>  
>  
>  
> > _______________________________________________
> > NSRCA-discussion mailing list
> > NSRCA-discussion at lists.nsrca.org(mailto:NSRCA-discussion at lists.nsrca.org)
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org(mailto:NSRCA-discussion at lists.nsrca.org)
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20171102/631cb46e/attachment.html>