[NSRCA-discussion] bullets

Wed Mar 30 06:10:26 AKDT 2011

 I now use the 4MM HK ones on everything. They work very well. The 6mm Hobby Kings are all over the place from batch to batch just as Verne is saying with the 5.5mm. The Hobby Kings ones do however melt very easily when connected the wrong way. The ensuing flash is also very colorful and quite spectacular. The pain felt on your finger tips and thumb is something else too. Mike

--- On Wed, 3/30/11, verne at twmi.rr.com <verne at twmi.rr.com> wrote:

> From: verne at twmi.rr.com <verne at twmi.rr.com>
> Subject: Re: [NSRCA-discussion] bullets
> To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
> Date: Wednesday, March 30, 2011, 8:42 AM
> FWIW, the 5.5 mm connectors I used
> were of the slotted variety. I ended up abandoning those
> after discovering too much variance from one manufacturer to
> the next and sometimes within the same manufacturer. I had
> connectors that ranged all the way from too loose to make a
> good connection to so tight that you couldn't put them
> together. The bulge you mention in the 4mm connectors is
> actually the "spring" that compensates for slight tolerance
> variances. I agree that there's not as much contact area as
> the slotted type, but it comes down to how much is enough?
> From my experience, the 4mm work just fine without the
> hassle of trying to find connectors to match what you've
> already got on all your batteries, charge leads, and so on.
> It gets a little pricey to start all over and I've done it
> twice. With the 4mm, I just add as I go without a hitch.
> 
> Verne 
> 
> 
> 
> ---- Ronald Van Putte <vanputte at cox.net>
> wrote: 
> 
> =============
> I have gotten these "no bulge/slotted design" connectors
> from two  
> sources:  HobbyKing and BidProduct.  You have to
> look at the pictures  
> carefully to see that they are the "no bulge/slotted
> design".
> 
> I really like BidProduct for acquiring large quantities of
> the  
> smaller items, like connectors, extensions and hardware for
> my small  
> hobby shop.  Many items can be purchased with free
> shipping.
> 
> Ron
> 
> On Mar 30, 2011, at 4:09 AM, Houdini76 at aol.com
> wrote:
> 
> > Ron, what brand of connectors has the no bulge/slotted
> design?  Do  
> > you use 4, 5 or 6mm?
> >
> > Rob
> >
> >
> > In a message dated 3/29/2011 8:01:08 P.M. Eastern
> Daylight Time,  
> > vanputte at cox.net
> writes:
> > Good stuff Verne.
> >
> > I have noticed the difference in bullet connector
> design.  I used  
> > to buy 3.5mm bullet connectors which had a "bulge" in
> the center of  
> > the male part.  Recently, I noticed some 3.5mm
> bullet connectors  
> > which had no "bulge" in the male part.  They push
> into the female  
> > part because there's a chamfer on the tip of the male
> part, which  
> > compresses the slotted male connector so it will fit
> into the  
> > female part.  The big advantage of this design is
> that virtually  
> > all of the connector is mated with the other half,
> unlike the ones  
> > with a "bulge", which have significantly reduced
> contact area.   
> > Then I noticed that you can buy this same design in
> 4mm, 5mm and  
> > 6mm bullet connectors.  My opinion - these are
> far superior.
> >
> > Ron
> >
> > On Mar 29, 2011, at 6:30 PM, Verne Koester wrote:
> >
> >> Jerry,
> >>
> >> I started out with Deans Ultra’s. They worked
> fine but didn’t wear  
> >> too well. The arc from connecting them together
> was really chewing  
> >> them up. Then I switched to 5.5mm bullets. Those
> worked great and  
> >> the arc did damage where it didn’t matter. The
> problem I  
> >> discovered later was when I needed some more. Not
> all 5.5mm are  
> >> created equal and I ran into some serious fit
> problems from one  
> >> batch to the next. I noticed that most of the
> Europeans were using  
> >> 4mm bullets. These are made a little different
> than the 5.5mm  
> >> and     have more “spring”
> in them so the tolerances don’t have to  
> >> be so close. Like the 5.5mm bullets, the arc
> damage happens on the  
> >> very tip which is not part of the actual
> electrical connection.  
> >> I’ve been very happy with the 4mm bullets and
> will be starting my  
> >> third season with them. BTW, I never noticed any
> power changes  
> >> from the Deans to the 5.5’s to the 4’s. Hope
> this helps.
> >>
> >>
> >>
> >> Verne Koester
> >>
> >>
> >>
> >> From: nsrca-discussion-bounces at lists.nsrca.org
> [mailto:nsrca- 
> >> discussion-bounces at lists.nsrca.org]
> On Behalf Of Jerry Stebbins
> >> Sent: Tuesday, March 29, 2011 5:29 PM
> >> To: Discussion -NSRCA
> >> Subject: [NSRCA-discussion] bullets
> >>
> >>
> >>
> >> All E's. What size bullets have you settled on for
> your packs/ESC  
> >> connections? Seems like something that would sorta
> get  
> >> standardized after a lot of 70A usage. I have
> heard from 3.5 to  
> >> 6.0. Would think it would work itself out to
> support the nominal  
> >> max. I that most see. I am sure 3D needs all they
> can get but for  
> >> AMA/FAI patterns seems like it otta round off
> pretty close for  
> >> most using 5s packs.
> >>
> >> Thanks ahead
> >>
> >> Jerry
> >>
> >> _______________________________________________
> >> NSRCA-discussion mailing list
> >> NSRCA-discussion at lists.nsrca.org
> >> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >
> > =
> >
> > _______________________________________________
> > NSRCA-discussion mailing list
> > NSRCA-discussion at lists.nsrca.org
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> > _______________________________________________
> > NSRCA-discussion mailing list
> > NSRCA-discussion at lists.nsrca.org
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion