[NSRCA-discussion] Fwd: Your Mount from Budd Eng

[Bob Lavey]

Did anyone else get 5 copies of this email?  Or was it just me?

 

From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Vicente "Vince" Bortone
Sent: Wednesday, June 08, 2011 8:21 AM
To: NSRCA NSRCA
Cc: Merle Hyde
Subject: [NSRCA-discussion] Fwd: Your Mount from Budd Eng

 

Mr. Merle Hyde asked me to forward to the list the e-mail below.

Thanks,

Vicente "Vince" Bortone

----- Forwarded Message -----
From: "Merle Hyde" <hydesoftmounts at yahoo.com>
To: "Vicente Vince Bortone" <vicenterc at comcast.net>
Sent: Tuesday, June 7, 2011 10:38:34 PM
Subject: Re: Your Mount from Budd Eng

Hi Vince,

Thanks for getting back to me.  Yes, I rec'd the mount from Budd Engineering and with the paper work enclosed I then realized it is Vic Koenigs mount.  I am a NSRCA member but simply do not participate in the discussion site.

If you can, would you please correct the NSRCA disscussion(s) that has prompted others to respond to a posting concering a mount I had made.  As I understand it, the heading of the posting was for someone to provide my mailing address, but the underlying and obiviously intended purpose was to encourage negative opinions of Hyde Mounts and/or bonding.  A CORRECTION to the NSRCA site should simply refer to the general context of the incorrect posting, that basically stated: the Hyde Mount rubber became de-bonded from the front disk during normal usage in a SPA Pattern Plane.

The honest and genuine facts are that the ORIGNIAL rubber was still attached to this Hyde Mount and the originial bonding was in superior condition and DID NOT FAIL...............  Also, the mount was in the age range of approximately 8 to 15 years old, and someone attempted to apply additional rubber utilizing a different bonding method.  The added rubber bonding is what actually FAILED/DE-BONDED!!!!!!!!!!!  

SOMEONE, obiviously not Vic Koenig, attempted to add the extra rubber, using another bonding method and the EXTRA rubber bonding process FAILED.  

Much is misunderstood about my mounts - obiviously someone over the years did not realize the mount was originally designed and identified as being a very very soft mount, with confirmed vibration reduction by actual engineers, to be in the vibration reduction range of 95%, and I suggested that design to be used with a nose ring.  Who ever had this mount, obiviously not Vic originally, at some point in time over the past 8 to 15 years decided the mount was too soft and decided to add additional rubber, expecting obiviously to use it without a nose ring.

Additionally, the extra added rubber bonding method was not even remotely similiar to my original rubber bond - and again, MY ORIGINAL RUBBER BOND DID NOT FAIL......

Appreciate you using many of my mounts over the years and the positive comment concerning the DA100 mount you obtained from me several years ago.

Best Regards.

Sincerely,

Merle

Merle Hyde3 Golf View Dr.Henderson, NV 89074U.S.A. Ph/Fax (011)702-269-7829Email:hydesoftmounts at yahoo.com


--- On Sun, 6/5/11, Vicente "Vince" Bortone <vicenterc at comcast.net> wrote:

> From: Vicente "Vince" Bortone <vicenterc at comcast.net>
> Subject: Re: Your Mount from Budd Eng
> To: "Merle Hyde" <hydesoftmounts at yahoo.com>
> Date: Sunday, June 5, 2011, 3:50 AM
> Hi Merle,
> 
> Good to hear from you.  That is not my mount. 
> Jerry Budd asked at the pattern opinion group for your
> address.  I just responded with your information. 
> Check with more detail the package.  There should be
> another person.
> 
> Going to attend tha FAI-F3a WC.  I know that Chip and
> USA team will do a nice job for us.
> 
> As you know I am using you soft mounts in all my pattern
> and IMAC planes.  The one you made for the DA-100 is
> working great after many years.    
> 
> Thanks,
> 
> Vicente "Vince" Bortone
> ----- Original Message -----
> From: Merle Hyde <hydesoftmounts at yahoo.com>
> To: vicenterc at comcast.net
> Sent: Sat, 04 Jun 2011 23:49:32 -0000 (UTC)
> Subject: Your Mount from Budd Eng
> Hi Vince,
> Today I received one of my mounts you had send to Jerry.
> Please give me a little back ground on that mount, such
> as:
> When did your purchase it?
> From whom did you purchase it?
> Approximate number of flights on it?
> Describe type of installation, such as, was it used with or
> without a nose ring.
> Am anxious to hear from you.
> SIncerely,
> Merle
> Merle Hyde3 Golf View Dr.Henderson, NV 89074U.S.A. Ph/Fax
> (011)702-269-7829Email:hydesoftmounts at yahoo.com
>





-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20110608/455687b9/attachment.html>