[NSRCA-discussion] Need Dremel Part

[Ron Van Putte]

Your contribution to SS is good for a judging bribe, but only for the  
Prelims.  Oh wait, you fly in the Master class and so do I; sorry.

Ron VP

On Jul 7, 2010, at 8:29 AM, Atwood, Mark wrote:

> Now I'm scared...we're using the same phone.
>
> My apps bigger than your app....
>
> Regarding SS, does this mean I've already paid my judging bribe to  
> you??
>
>
>
> Mark Atwood
> Paragon Consulting, Inc.  |  President
> 5885 Landerbrook Drive Suite 130, Cleveland Ohio, 44124
> Phone: 440.684.3101 x102  |  Fax: 440.684.3102
> mark.atwood at paragon-inc.com  |  www.paragon-inc.com
>
> -----Original Message-----
> From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca- 
> discussion-bounces at lists.nsrca.org] On Behalf Of Ron Van Putte
> Sent: Wednesday, July 07, 2010 9:26 AM
> To: General pattern discussion
> Subject: Re: [NSRCA-discussion] Need Dremel Part
>
> To get the record straight:  I retired from the USAF in 1979, from
> Civil Service in 1997 and started collecting Social Security the same
> year.  You youngsters will never see Social Security, so I thank each
> and every one of you for my monthly check.
>
> Now about keeping up with the times:  My cell phone is a Droid
> Incredible.  What's yours whippersnapper?
>
> Ron VP
>
> On Jul 7, 2010, at 8:12 AM, Atwood, Mark wrote:
>
>> Better screws on the coffin lid??
>>
>> Seriously though, as one who still has my Dremel from 1973 (I know,
>> you were already retired then right??) I finally broke down and
>> bought a new one and have been wondering why I waited so long.  The
>> newer cordless lithium powered units rock.  Take the plunge...
>>
>> Mark Atwood
>> Paragon Consulting, Inc.  |  President
>> 5885 Landerbrook Drive Suite 130, Cleveland Ohio, 44124
>> Phone: 440.684.3101 x102  |  Fax: 440.684.3102
>> mark.atwood at paragon-inc.com  |  www.paragon-inc.com
>>
>>
>> -----Original Message-----
>> From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-
>> discussion-bounces at lists.nsrca.org] On Behalf Of Ron Van Putte
>> Sent: Tuesday, July 06, 2010 2:58 PM
>> To: General pattern discussion
>> Subject: [NSRCA-discussion] Need Dremel Part
>>
>> I have an old Dremel Freewheeler Model 850 that has a flexible
>> coupler between the motor and the output shaft.  This coupler is
>> splined on the inside and the splines finally wore out after 20+
>> years for no reason at all.  It's on its third or fourth battery
>> pack, but still worked fine before the coupler gave out. I've tried
>> searching sources for Dremel parts but can't find what I need.  I
>> would just buy a new one, but I am stubborn and the son of a Scottish
>> mother, who would rise up out of her grave if I did.
>>
>> Any ideas?
>>
>> Ron Van Putte
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion