[NSRCA-discussion] Iota 55 power supply questions

Mon Sep 28 18:50:38 AKDT 2009

The Iota only has one positive and one negative post. I cut two strips of K&S brass about ¼ wide, .090 thick, and two inches long to make two lugs (one positive and one negative) similar to what you plug into a typical 110v wall outlet. On one end of each of those lugs, I soldered the wires directly from my chargers, pos to pos and neg to neg plus an additional wire for an auxiliary banana plug outlet. Then I put heat shrink over the wires and solder joint so there was just enough bare brass showing to insert into each of the outputs from the Iota. The Iota has set screws that clamp down onto the brass strips. Works fine. When you get your Iota, this explanation will make sense. If you want a more “flexible” setup, you could go with all banana jacks to facilitate plugging and unplugging your chargers as you choose. If I had to remove mine for repairs or whatever, I’d have to unsolder the connections. Haven’t had the need so far with either the 1010’s or the CellPros.

Verne

From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Anthony Abdullah
Sent: Monday, September 28, 2009 4:49 PM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] Iota 55 power supply questions

Thank you Mr. Mueller!

Question, does that power supply have the dual outputs on it to allow me to hook two chargers to it? It is really convenient to be able to plug banana plugs right into the power supply as I currently do with my Pro Peak. From the looks of it, that is not necessarily designed for "civilized" hobby use. I am looking for something that can power two 1010C chargers with reliable clean power that I can just plug right into, or "Idiot Resistant" as my momma would say.

  _____  

From: mike mueller <mups1953 at yahoo.com>
To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
Sent: Monday, September 28, 2009 4:23:19 PM
Subject: Re: [NSRCA-discussion] Iota 55 power supply questions

http://cgi.ebay.com/ebaymotors/Iota-DLS-55-amp-RV-Power-Converter-Battery-Charger_W0QQcmdZViewItemQQ_trksidZp3286Q2ec0Q2em14QQhashZitem2c50ff1fbfQQitemZ190337458111QQptZMotorsQ5fRVQ5fTrailerQ5fCamperQ5fPartsQ5fAccessories
Here's where I bought my last one. Good luck Sponge Bob, Mike

--- On Mon, 9/28/09, Dave <DaveL322 at comcast.net> wrote:

> From: Dave <DaveL322 at comcast.net>
> Subject: Re: [NSRCA-discussion] Iota 55 power supply questions
> To: "'General pattern discussion'" <nsrca-discussion at lists.nsrca.org>
> Date: Monday, September 28, 2009, 2:40 PM
> 
> 
> 
>  
>  
> 
>  
> 
>  
> 
>  
> 
> 
> 
> 
> 
> 
> 
>  
> 
> 
> 
> Yes, 4
> 1010s at 10s 5amps each running
> from 2 Iota 55s is no problem with the 2kw Honda.  You
> could add 1 more
> 1010 on each Iota and have about 3 amps at 10s left for
> each.  No, I don’t
> have 6 1010s…..but the 2kw generator is popular at
> the field <G>. 
> 
> 
>   
> 
> I leave the
> small voltage jumper plug in
> my Iotas all the time – bumps output voltage from
> something like 13.4 to
> 14.2V, which should make the 1010s run a little more
> efficiently. 
> 
> 
>   
> 
> Dave
> 
> 
> 
>   
> 
> 
>   
> 
> 
>   
> 
> 
>   
> 
> 
> 
> 
> 
> 
> 
> 
> 
> From:
> nsrca-discussion-bounces at lists.nsrca.org
> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Earl Haury
> 
> Sent: Monday,
> September 28, 2009
> 3:20 PM
> 
> To:
> chad at f3acanada.org;
>  General pattern discussion
> 
> Subject: Re:
> [NSRCA-discussion]
> Iota 55 power supply questions 
> 
> 
> 
>    
> 
> 
> 
> I agree with
> Chad 
> - for a 1 kW Honda. You might consider 2 kW Honda for
> a little more $
> & weight. It will handle (at least)  two Iota
> 55's & 4
> 1010's as well as a couple of TX battery
> chargers with no problem.
> (If you live in an area that experiences occasional power
> outages the 2 kW
> Honda will handle a lot of household items
> also.) 
> 
> 
> 
> 
> 
>   
> 
> 
> 
> 
> 
> Earl
> 
> 
> 
> 
> 
> 
> 
> 
> ----- Original
> Message -----  
> 
> 
> 
> 
> 
> From: Chad
> Northeast  
> 
> 
> 
> 
> 
> To: General pattern
> discussion  
> 
> 
> 
> 
> 
> Sent: Monday,
> September
> 28, 2009 1:40 PM 
> 
> 
> 
> 
> 
> Subject: Re:
> [NSRCA-discussion] Iota 55 power supply
> questions 
> 
> 
> 
> 
> 
>    
> 
> 
> 
> Two is not a problem, the Iota 55 will
> handle two 1010's at full rate
> and a third set to about 4A (on 10s) when plugged into a
> household circuit.
> 
> 
> 
> Hooked up to the Honda you wont get the third up to more
> than around 2.5A
> before you trip it.  If you want to run the Honda to
> the max make sure the
> Eco switch is off and you can get a little more out of it.
> 
> 
> 
> I think the Iota has a 950W input requirement to get its
> max power, and the
> Honda is only rated to around 900W continuously or
> something.
> 
> 
> 
>  Chad
> 
> 
> 
> 
> 
> ----- Original Message -----
> 
> From: Anthony Abdullah < aabdu at sbcglobal.net >
> 
> Date: Monday, September 28, 2009 12:31 pm
> 
> Subject: [NSRCA-discussion] Iota 55 power supply questions
> 
> To: General pattern discussion 
> <nsrca-discussion at lists.nsrca.org>
> 
> 
> 
> > 
> 
> > I am making plans to get geared up for next
> season and have a 
> 
> > few questions about power supplies and such. I am
> looking to run 
> 
> > two Thunder Power 1010C chargers off of one Iota 55
> amp power 
> 
> > supply from a Honda generator. Is that
> feasable? Is there any 
> 
> > reason I would not be able to charge two 10S 5000
> packs at 5 
> 
> > amps each with that set up? Where is the best place to
> buy an 
> 
> > Iota power supply? Are their different models of that
> power 
> 
> > supply that should be considered?
> 
> > 
> 
> > Sorry for all of the questions, I just want to get the
> right 
> 
> > stuff the first time.
> 
> > 
> 
> > Thanks in advance
> 
> > Anthony  
> 
> 
> 
> 
> 
> 
> 
> _______________________________________________
> 
> NSRCA-discussion mailing list
> 
> NSRCA-discussion at lists.nsrca.org
> 
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> 
> 
> 
> 
> 
> 
>  
> 
> 
> 
> -----Inline Attachment Follows-----
> 
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20090929/01566353/attachment.html>