[NSRCA-discussion] Futaba Servos

[Ed Alt]

You run 1 ground wire for both. If you do this, test it well for interaction between the two servos.
  ----- Original Message ----- 
  From: brian young 
  To: General pattern discussion 
  Sent: Friday, December 11, 2009 9:07 AM
  Subject: Re: [NSRCA-discussion] Futaba Servos


  What was the servo extension wire trick? Separate the power wires from signal or something?




------------------------------------------------------------------------------
  From: krishlan fitzsimmons <homeremodeling2003 at yahoo.com>
  To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
  Sent: Thu, December 10, 2009 11:43:49 PM
  Subject: Re: [NSRCA-discussion] Futaba Servos


  If you are not trying to be brand specific, and it's going in an electric, I have been using the Airtronics digital 94761's on ele's and aileron's for 2 or 3 seasons now. Not trying to sell you on the one's I use, but they are an option to save weight if you need it. I think they weight .80 ou. and have 66 ounces of torque at 6.0v.  I am also running the newer 746's though and they do feel a little different in a better way. The 761's had a great fast snap and a quick stop to the snap. Can't say I noticed any difference between the two on the snap. 

  Where else have you tried to save weight? 
  If you do the servo extension wire trick to the tail, you will save approximately 8 grams- .30 ou.. 

  Good luck with whatever you purchase. 
   
  Chris 








------------------------------------------------------------------------------
  From: Dave Burton <burtona at atmc.net>
  To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
  Sent: Thu, December 10, 2009 7:00:26 PM
  Subject: Re: [NSRCA-discussion] Futaba Servos

  Thanks for the responses guys. I have a couple of JR 9411 SA for the
  ailerons to swap out but was looking for something even lighter if they
  would work. I need to get about 4-5 oz. Out of this bird.
  Dave Burton

  -----Original Message-----
  From: nsrca-discussion-bounces at lists.nsrca.org
  [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of J Shu
  Sent: Thursday, December 10, 2009 5:54 PM
  To: General pattern discussion
  Subject: Re: [NSRCA-discussion] Futaba Servos

  I've flown the same design plane, one with 9650's and the other with 9151's,
  and there was a difference. The one with the 51's was a 
  much better (predictable) snapping plane. The 50's were speed sensitive
  (downlines were never the same).

  Andrew is right about the low profile Futaba's. I was running the BL-551,
  1.6oz, 
  (http://www.futaba-rc.com/servos/brushlessservos.html) in my Integrals and
  now in my Valiant. The 9551, 1.6oz, 
  (http://www.futaba-rc.com/servos/digitalservos.html) is the non-brushless
  version (that Andrew was running in his Integrals). The JR 
  9411 will also work fine, I just don't have experience with them.

  Regards,
  Jason
  www.shulmanaviation.com
  www..composite-arf.com

  ----- Original Message ----- 
  From: "Dave" <DaveL322 at comcast.net>
  To: "'General pattern discussion'" <nsrca-discussion at lists.nsrca.org>
  Sent: Thursday, December 10, 2009 5:30 PM
  Subject: Re: [NSRCA-discussion] Futaba Servos


  > Dave,
  >
  > Quite a few guys are running the JR 9411 on ailerons on 2M stuff.  You'll
  > save about 1.5 oz for the pair.
  >
  > Regards,
  >
  > Dave Lockhart, Team JR
  >
  >
  > -----Original Message-----
  > From: nsrca-discussion-bounces at lists.nsrca.org
  > [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Dave Burton
  > Sent: Thursday, December 10, 2009 5:07 PM
  > To: 'General pattern discussion'
  > Subject: [NSRCA-discussion] Futaba Servos
  >
  > I have a question about Futaba servos (I'm a JR user) from some Futaba
  > flyers.
  > Are the Futaba 9650 digital servos suitable for ailerons on an electric 2
  > meter plane (Intrgral)? I'm looking to save a couple ounces over the full
  > size JR 8411SA I'm using now.
  > Thanks,
  > Dave Burton
  >
  >
  > _______________________________________________
  > NSRCA-discussion mailing list
  > NSRCA-discussion at lists..nsrca.org
  > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
  >
  > _______________________________________________
  > NSRCA-discussion mailing list
  > NSRCA-discussion at lists.nsrca.org
  > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 

  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion







------------------------------------------------------------------------------


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20091211/5100de34/attachment.html>