[NSRCA-discussion] Thunder Power data cable ends

[rcmaster199 at aol.com]

  Ed's correct in regard to RTV silicone sealing compounds. They produce 
acetic acid upon curing.

However, silicone rubber designed for insulation purposes (different 
curing method than RTV) has one of the highest di-electric strengths we 
can produce. RTV is not one of these chemicals so be forewarned

MattK

-----Original Message-----
From: Ed Alt <ed_alt at hotmail.com>
To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
Sent: Mon, 8 Sep 2008 10:17 pm
Subject: Re: [NSRCA-discussion] Thunder Power data cable ends

Be careful about using silicon sealer.  It has
a tendency to corrode metal over time.  Try Walthers Goo.

  ----- Original Message -----
  From:
  Jay
  Marshall
  To: 'General pattern
  discussion'
  Sent: Monday, September 08, 2008 8:32
  PM
  Subject: Re: [NSRCA-discussion] Thunder
  Power data cable ends



  Something that has a
   little flex, such as silicone sealer, works better. If you have a 
hard,
  immovable joint the wire will tend to break there.
   


Jay
  Marshall
  -----Original
  Message-----
From:
  nsrca-discussion-bounces at lists.nsrca.org
  [mailto:nsrca-discussion-bounces at lists.nsrca.org]
  On Behalf Of Anthony
  Romano
Sent: Monday,
  September 08, 2008 8:32 PM
To: General pattern
  discussion
Subject: Re: [NSRCA-discussion] Thunder
  Power data cable ends
   
  Hi Scott,
 Good point.=2
0A
  little left over epoxy works well for that
  too!

Anthony






  Date:
  Mon, 8 Sep 2008 18:00:52 -0400
From: js.smith at verizon.net
To:
  nsrca-discussion at lists.nsrca.org
Subject: Re: [NSRCA-discussion] Thunder
  Power data cable ends

   
  I don’t have
   a source but if you get a new cable, pot the wires with a little 
JB-Weld at
  the connector.  This will keep the wires from breaking at the
   crimp.  Also, if you break off the locking tab, it’s easier to 
connect
  and disconnect.  
   
   
   

   
   
  -----Original
  Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
  [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Stuart
  Chale
Sent: Monday, September 08, 2008 11:04 AM
To: NSRCA Mailing
  List
Subject: [NSRCA-discussion] Thunder Power data cable
  ends
   
  Does anyone
  have a source for the 3 pin female data cable ends for the
  TP charger to
  balancer connection?
  They have a
  habit of breaking usually right at the pin making it
  difficult to
  repair.  A prewired pigtail or double female extension that

  could be cut
  in half would allow easy repairs and hopefully cheaper than
  $10 to
  replace the cable each time it breaks.
   
  Thanks,
  Stuart
  C.
  0
  _______________________________________________
  NSRCA-discussion mailing
  list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
   



  See how Windows connects the
  people, information, and fun that are part of your life. See Now





_______________________________________________
NSRCA-discussion
  mailing
  list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion