[NSRCA-discussion] Fuel soaked wood repair
John Ferrell
johnferrell at earthlink.net
Fri Nov 14 13:04:47 AKST 2008
If the oil got in there I would expect that the Clorox could also get in there, it might take a little time. You might have to get a little creative about reattaching glass to foam.
The problem does not have you beat until you give up!
John Ferrell W8CCW
"All that is necessary for the triumph of evil is for good men to do nothing." -- Edmund Burke
http://DixieNC.US
----- Original Message -----
From: Michael Cohen
To: nsrca-discussion at lists.nsrca.org
Sent: Thursday, November 13, 2008 9:26 PM
Subject: Re: [NSRCA-discussion] Fuel soaked wood repair
OK, what about oil that got in between fiberglass and foam. I have an Eclipse where that happened. Even though it is a backup plane, I would like to salvage it, if possible.
------------------------------------------------------------------------------
From: johnferrell at earthlink.net
To: nsrca-discussion at lists.nsrca.org
Date: Thu, 13 Nov 2008 20:14:20 -0500
Subject: Re: [NSRCA-discussion] Fuel soaked wood repair
Just slop it on!
It will remove oil from wherever it touches OR the vapor reaches. I recommend it be done outside and you must consider the effects of getting everything wet.
Oil up a piece of scrap balsa and then soak it in Clorox. After it dries you will have removed all oil.
John Ferrell W8CCW
"All that is necessary for the triumph of evil is for good men to do nothing." -- Edmund Burke
http://DixieNC.US
----- Original Message -----
From: John Konneker
To: Discussion List ; jpavlick at idseng.com
Sent: Thursday, November 13, 2008 3:20 PM
Subject: Re: [NSRCA-discussion] Fuel soaked wood repair
Hey John,
What's the technique you use with Clorox?
Do you apply it and then just mop it up?
Thanks!
JLK
----------------------------------------------------------------------------
From: johnferrell at earthlink.net
To: jpavlick at idseng.com; nsrca-discussion at lists.nsrca.org
Date: Thu, 13 Nov 2008 15:04:53 -0500
Subject: Re: [NSRCA-discussion] Fuel soaked wood repair
Full strength Clorox Bleach works best. It destroys the oil, works fast. It also will remove oil from everything that will rust!
John Ferrell W8CCW
"All that is necessary for the triumph of evil is for good men to do nothing." -- Edmund Burke
http://DixieNC.US
----- Original Message -----
From: John Pavlick
To: General pattern discussion ; shinden1 at cox.net
Sent: Tuesday, November 11, 2008 2:45 PM
Subject: Re: [NSRCA-discussion] Fuel soaked wood repair
Cool - that sounds good too. Since I own a few Harleys I always have plenty of "Speedy-Dry" (floor dry) on hand!
I actually found some K2R at the local hardware store today so now I have 2 methods that might help me save this airplane. :)
John Pavlick
--- On Tue, 11/11/08, shinden1 at cox.net <shinden1 at cox.net> wrote:
From: shinden1 at cox.net <shinden1 at cox.net>
Subject: Re: [NSRCA-discussion] Fuel soaked wood repair
To: jpavlick at idseng.com, "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
Date: Tuesday, November 11, 2008, 3:31 PM
John
I`ve have used k2R in the past but,
But I find the best way is use a good amount of Acetone soaked on a rag scrub
the parts you need cleaned real good leaving some Acetone soaked in the wood ,
Then, fill the nose with " floor dry "Or "kitty litter"
floor dry is better ,,,
you can buy a bag at the local Car Parts store
then place a heat lamp over the area ,,,even make a box or cover ,, to trap the
heat
and over night it will be dry as a bone,
it`s kinda messy But it`s the best way I`ve found so far and,
it will draw the oil out completely
Bryan
---- John Pavlick <jpavlick at idseng.com> wrote:
>
> OK, looks like K2R is the magic potion. Oddly enough this stuff is made
right in Derby, CT (I'm in New Milford, CT). I'll try to find it at the
hardware store today (Ace and True Value are suppposed to carry the stuff). If
they don't have it, I found a place that sells it online. Thanks everyone
- if this works as well as you say I should be able to buy some time for this
airplane after all. Of course just how much time that is depends on the pilot...
>
> John Pavlick
>
> --- On Tue, 11/11/08, John Konneker <jlkonn at hotmail.com> wrote:
>
> From: John Konneker <jlkonn at hotmail.com>
> Subject: Re: [NSRCA-discussion] Fuel soaked wood repair
> To: "Discussion List" <nsrca-discussion at lists.nsrca.org>
> Date: Tuesday, November 11, 2008, 1:08 PM
>
>
>
>
> #yiv970774449 .hmmessage P
> {
> margin:0px;padding:0px;}
> #yiv970774449 {
> font-size:10pt;font-family:Verdana;}
>
> I too have bought K2R in the past couple months at Ace Hardware.
> I couldn't find it anywhere else...
> JLK
>
>
>
>
>
> From: lightfoot at sc.rr.com
> To: nsrca-discussion at lists.nsrca.org
> Date: Tue, 11 Nov 2008 07:40:04 -0500
> Subject: Re: [NSRCA-discussion] Fuel soaked wood repair
>
>
>
>
> #yiv970774449 .ExternalClass p.EC_MsoNormal, #yiv970774449 .ExternalClass
li.EC_MsoNormal, #yiv970774449 .ExternalClass div.EC_MsoNormal
> {margin-bottom:.0001pt;font-size:12.0pt;font-family:'Times New
Roman';}
> #yiv970774449 .ExternalClass a:link, #yiv970774449 .ExternalClass
span.EC_MsoHyperlink
> {color:blue;text-decoration:underline;}
> #yiv970774449 .ExternalClass a:visited, #yiv970774449 .ExternalClass
span.EC_MsoHyperlinkFollowed
> {color:blue;text-decoration:underline;}
> #yiv970774449 .ExternalClass p
> {margin-right:0in;margin-left:0in;font-size:12.0pt;font-family:'Times
New Roman';}
> #yiv970774449 .ExternalClass span.EC_EmailStyle18
> {font-family:Arial;color:navy;}
> _filtered #yiv970774449 {}
> #yiv970774449 .ExternalClass div.EC_Section1
> {}
>
>
>
> Saw some K2 AT Ace Hardware last month. Google it.
>
> Jay Marshall
>
> -----Original Message-----
> From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of MKMSG
> Sent: Monday, November 10, 2008 10:23 PM
> To: General pattern discussion
> Subject: Re: [NSRCA-discussion] Fuel soaked wood repair
>
>
> John: Don't know if they still sell it, but K2R spot remover worked
great when I used it years ago. Put it on, let it dry, and vacuum it off. A
couple of applications might be needed, but it did work.
>
>
>
> Mike
>
>
> ----- Original Message -----
>
> From: John Pavlick
>
> To: NSRCA Discussion
>
> Sent: Monday, November 10, 2008 9:10 PM
>
> Subject: [NSRCA-discussion] Fuel soaked wood repair
>
>
>
> I'm trying to repair one of my friend's airplanes (broken landing
gear plate) and unfortunately it's pretty well soaked with fuel in the tank
area. I've never had much luck trying to get fuel out of wood other than
soaking it with CA. Is there anything I can do or is it hopeless?
>
>
>
> John Pavlick
> http://www.idseng.com
>
>
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion_______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
--------------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
----------------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
------------------------------------------------------------------------------
Windows Live Hotmail now works up to 70% faster. Sign up today.
------------------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20081114/84ebed4f/attachment.html>
More information about the NSRCA-discussion
mailing list