[NSRCA-discussion] Embarrassing Programming Problem - Inventing the wheel...

[Bob Kane]

I had attributed a higher moral standard to the creation of the wheel, now the truth is revealed. 

But then again, it came from Mark . . . . . . . .


 Bob Kane
getterflash at yahoo.com



----- Original Message ----
From: Mark Atwood <atwoodm at paragon-inc.com>
To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
Sent: Tuesday, May 6, 2008 2:08:30 PM
Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem - Inventing the wheel...

For those that want to see Ron in his younger days...  A reenactment.

http://www.youtube.com/watch?v=oTLy6EBmd5s


On 5/6/08 1:57 PM, "george w. kennie" <geobet at gis.net> wrote:

> I remember !   What a tough time we had sanding those corners down. If only
> we had thought to balance them.
> G.
> 
> 
> 
> ----- Original Message -----
> From: "Ron Van Putte" <vanputte at cox.net>
> To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
> Sent: Monday, May 05, 2008 4:55 PM
> Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem
> 
> 
>> I was not around when the wheel was first invented.  However, I
>> participated in the first post production design iteration:  Making
>> them round to get rid of the "clunk, clunk, clunk".
>> 
>> Ron
>> 
>> On May 5, 2008, at 3:24 PM, Mark Atwood wrote:
>> 
>>> Because he was around when it was invented the first time???
>>> 
>>>  :):):):)
>>> 
>>> 
>>> 
>>> 
>>> On 5/5/08 4:20 PM, "Tony" <tony at radiosouthrc.com> wrote:
>>> 
>>>> Ron:
>>>> Why are you re-inventing the wheel?
>>>> Use the Ailvator pre-set mix for dual elevator servos already
>>>> built into the
>>>> 9Z..
>>>> 
>>>> 
>>>> Tony Stillman, President
>>>> Radio South, Inc.
>>>> 139 Altama Connector, Box 322
>>>> Brunswick, GA  31525
>>>> 1-800-962-7802
>>>> www.radiosouthrc.com
>>>> 
>>>> -----Original Message-----
>>>> From: nsrca-discussion-bounces at lists.nsrca.org
>>>> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ron
>>>> Van Putte
>>>> Sent: Monday, May 05, 2008 4:09 PM
>>>> To: General pattern discussion
>>>> Subject: [NSRCA-discussion] Embarrassing Programming Problem
>>>> 
>>>> I'm setting up a new airplane on my Futaba 9ZAP transmitter and using
>>>> channels 2 and 6 for servos on each elevator half.  I have PMX set
>>>> for channels 2 and 6, mixing channel 2 into channel 6 and everything
>>>> works fine, except the servo on channel 6 only moves about 2/3 the
>>>> throw of the servo on channel 2.  I've tried everything I can think
>>>> of to rectify the problem with no success.  In addition, there's a
>>>> small shift in neutral when going from high rate elevator to low
>>>> rate.
>>>> 
>>>> I started with an unused model in the menu, so I don't think there's
>>>> any hidden programming lurking.
>>>> 
>>>> Any ideas?  I'll be very irritated to find there's a simple solution,
>>>> but I'd also be very grateful to have the problem go away.
>>>> 
>>>> Ron Van Putte
>>>> _______________________________________________
>>>> NSRCA-discussion mailing list
>>>> NSRCA-discussion at lists.nsrca.org
>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>> 
>>>> _______________________________________________
>>>> NSRCA-discussion mailing list
>>>> NSRCA-discussion at lists.nsrca.org
>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>> 
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>> 
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>> 
> 

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion



      ____________________________________________________________________________________
Be a better friend, newshound, and 
know-it-all with Yahoo! Mobile.  Try it now.  http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20080506/64c7a457/attachment-0001.html