[NSRCA-discussion] Embarrassing Programming Problem

[george w. kennie]

I remember !   What a tough time we had sanding those corners down. If only 
we had thought to balance them.
G.



----- Original Message ----- 
From: "Ron Van Putte" <vanputte at cox.net>
To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
Sent: Monday, May 05, 2008 4:55 PM
Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem


>I was not around when the wheel was first invented.  However, I
> participated in the first post production design iteration:  Making
> them round to get rid of the "clunk, clunk, clunk".
>
> Ron
>
> On May 5, 2008, at 3:24 PM, Mark Atwood wrote:
>
>> Because he was around when it was invented the first time???
>>
>>  :):):):)
>>
>>
>>
>>
>> On 5/5/08 4:20 PM, "Tony" <tony at radiosouthrc.com> wrote:
>>
>>> Ron:
>>> Why are you re-inventing the wheel?
>>> Use the Ailvator pre-set mix for dual elevator servos already
>>> built into the
>>> 9Z..
>>>
>>>
>>> Tony Stillman, President
>>> Radio South, Inc.
>>> 139 Altama Connector, Box 322
>>> Brunswick, GA  31525
>>> 1-800-962-7802
>>> www.radiosouthrc.com
>>>
>>> -----Original Message-----
>>> From: nsrca-discussion-bounces at lists.nsrca.org
>>> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ron
>>> Van Putte
>>> Sent: Monday, May 05, 2008 4:09 PM
>>> To: General pattern discussion
>>> Subject: [NSRCA-discussion] Embarrassing Programming Problem
>>>
>>> I'm setting up a new airplane on my Futaba 9ZAP transmitter and using
>>> channels 2 and 6 for servos on each elevator half.  I have PMX set
>>> for channels 2 and 6, mixing channel 2 into channel 6 and everything
>>> works fine, except the servo on channel 6 only moves about 2/3 the
>>> throw of the servo on channel 2.  I've tried everything I can think
>>> of to rectify the problem with no success.  In addition, there's a
>>> small shift in neutral when going from high rate elevator to low
>>> rate.
>>>
>>> I started with an unused model in the menu, so I don't think there's
>>> any hidden programming lurking.
>>>
>>> Any ideas?  I'll be very irritated to find there's a simple solution,
>>> but I'd also be very grateful to have the problem go away.
>>>
>>> Ron Van Putte
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> 


-- 
I am using the free version of SPAMfighter for private users.
It has removed 7139 spam emails to date.
Paying users do not have this message in their emails.
Get the free SPAMfighter here: http://www.spamfighter.com/len