[NSRCA-discussion] Epoxy Question

[Scott Anderson]

yep in the 70"s here in Knoxville, TN.

Scott A.
----- Original Message ----- 
From: "Pete Cosky" <pcosky at comcast.net>
To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
Sent: Wednesday, November 21, 2007 9:20 PM
Subject: Re: [NSRCA-discussion] Epoxy Question


> FWIW - It was 72 today in Pittsburgh and sunny (we only get 4 or 5 sunny 
> days a year here) so I decided on rum.
> 
> Back to the basement so I can sheet my wings.
> 
> ----- Original Message ----- 
> From: "Ron Van Putte" <vanputte at cox.net>
> To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
> Sent: Wednesday, November 21, 2007 5:41 PM
> Subject: Re: [NSRCA-discussion] Epoxy Question
> 
> 
>> What does the temperature have to do with whether to have a beer?
>>
>> It's 70 degrees here today in the Florida panhandle, but it's very
>> cloudy (sob!).
>>
>> Ron
>>
>> On Nov 21, 2007, at 4:26 PM, J N Hiller wrote:
>>
>>> I'm with you Ron but it is kind off season here. It got up to about 35
>>> today.
>>> Jim
>>>
>>>  -----Original Message-----
>>> From: nsrca-discussion-bounces at lists.nsrca.org
>>> [mailto:nsrca-discussion-bounces at lists.nsrca.org]  On Behalf Of Ron
>>> Van
>>> Putte
>>> Sent: Wednesday, November 21, 2007 1:26 PM
>>> To: NSRCA Mailing List
>>> Subject: Re: [NSRCA-discussion] Epoxy Question
>>>
>>> Nah.  That's not a no-brainer.  A no-brainer is whether to have
>>> another beer.
>>>
>>> Ron
>>>
>>> On Nov 21, 2007, at 3:13 PM, wgalligan wrote:
>>>
>>>> If this question was raised as a method for skinning wings, then
>>>> why not use
>>>> urethane glue. One part, spreads easy and cures hard and quickly
>>>> with plain
>>>> ole 02moisture.  Gives ample working time and unlike epoxy will
>>>> expand with
>>>> moisture to fill voids and between foam beads.  Available at local
>>>> hardware
>>>> stores and less expensive.
>>>>
>>>> Seems like a no-brainer to me.
>>>>
>>>> Wayne Galligan
>>>>
>>>> ----- Original Message -----
>>>> From: "J N Hiller" <jnhiller at earthlink.net>
>>>> To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
>>>> Sent: Wednesday, November 21, 2007 2:00 PM
>>>> Subject: [NSRCA-discussion] Epoxy Question
>>>>
>>>>
>>>>> Thin Epoxy? I have been using "HOBBYPOXY SMOOTH 'N' EASY" epoxy
>>>>> finishing
>>>>> resin to skin foam wings, spreading it with a scrap balsa
>>>>> squeegee. It has
>>>>> ample working time and is thinner than glue. Is this OK? I have
>>>>> had no
>>>>> problems using it on unsealed skins at about one ounce per 800
>>>>> square
>>>>> inches. I need to try sealing the skins on my next build.
>>>>> Jim Hiller
>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>> --------------------------------------------------------------------- 
>>>> -
>>>> ----------
>>>>
>>>>
>>>>> _______________________________________________
>>>>> NSRCA-discussion mailing list
>>>>> NSRCA-discussion at lists.nsrca.org
>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>>
>>>>>
>>>>
>>>> _______________________________________________
>>>> NSRCA-discussion mailing list
>>>> NSRCA-discussion at lists.nsrca.org
>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>> 
> 
> 
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion