[NSRCA-discussion] Nice flying day.

[jivey61 at bellsouth.net]

If anyone has any thoughts about controlling the vibrations on the rod please tell me your secrets. thanks.
Matt...vibrations are caused by worn connectors,arms,and bad geometry arangement. Ailerons not sealed,and bad or worn feedback pots in the servos and worn output bearings(top). Get someone to check the servo for pot troubleand make sure it's all jam up and jelly tight.
Jim Ivey
  ----- Original Message ----- 
  From: R. LIPRIE 
  To: NSRCA Mailing List 
  Sent: Sunday, January 28, 2007 7:21 PM
  Subject: Re: [NSRCA-discussion] Nice flying day.


  Ya JR digital servos.  I'm lucky I got it back on the ground.  Brought it to the tabel and hugged it.lol.

    ----- Original Message ----- 
    From: jivey61 at bellsouth.net 
    To: NSRCA Mailing List 
    Sent: Sunday, January 28, 2007 6:25 PM
    Subject: Re: [NSRCA-discussion] Nice flying day.


    Matt
     .You didn't say what kind of servos.If you are using JR digital servos with the metric screws holding the servo arm on,you need to use locktight (blue) on the screw and tighten it good.I had one come off the aileron and it cost me a plane.
    Jim Ivey
      ----- Original Message ----- 
      From: R. LIPRIE 
      To: MATTS NSRCA 
      Sent: Sunday, January 28, 2007 6:50 PM
      Subject: [NSRCA-discussion] Nice flying day.


      Hello all,

      Finally had some good weather to go flying, today.
      Blue Skies, wind calm.

      Had a malfunction that almost costed me my $3000 dollar plane.  Okay I was in the middle of the Intermediate pattern.  And suddenly I noticed that it was rolling extremely slower than it was when I started the pattern.
      So I told Uncle Mike,that I was gonna go ahead and bring it on in.  So turned around came in for a approach and got a little slow and the that one aileron really wasn't working well going that slow.  So I chopped the throttle and set her down in the grass. And so the mud caught it and made the nose dig into the mud.  (Globs of it were on the plane)..  RAN there to see what the problem was.  To find that my screw came off of the left control rod on the left aileron and absolutely detached the rod from the servo leaving the aileron just dangling in the wind....  Brought it in cleaned it up got a new screw and tightened it as tight as I could get it.   And went ahead and flew one more time.  No problem.

      Like I said it was better to get mud all over the airplane than to have it in pieces.  So I saved the day.  Very happy.
      /
      If anyone has any thoughts about controlling the vibrations on the rod please tell me your secrets. thanks

      Matthew Liprie


--------------------------------------------------------------------------


      _______________________________________________
      NSRCA-discussion mailing list
      NSRCA-discussion at lists.nsrca.org
      http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


----------------------------------------------------------------------------


    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 


----------------------------------------------------------------------------


    No virus found in this incoming message.
    Checked by AVG Free Edition.
    Version: 7.5.432 / Virus Database: 268.17.12/655 - Release Date: 1/28/2007 1:12 PM



------------------------------------------------------------------------------


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20070129/1fe3dd92/attachment.html