[NSRCA-discussion] Controll Systems

[Rex LESHER]

You betcha!!!
Looks like they changed them...  No more frame over the top of the entire servo, just an end piece through two servo screws.

Rex

  ----- Original Message ----- 
  From: Ken Thompson<mailto:mrandmrst at comcast.net> 
  To: NSRCA Mailing List<mailto:nsrca-discussion at lists.nsrca.org> 
  Sent: Thursday, January 11, 2007 8:44 PM
  Subject: Re: [NSRCA-discussion] Controll Systems


  thanks Rex.
    ----- Original Message ----- 
    From: Rex LESHER<mailto:trexlesh at msn.com> 
    To: NSRCA Mailing List<mailto:nsrca-discussion at lists.nsrca.org> 
    Sent: Thursday, January 11, 2007 9:57 PM
    Subject: Re: [NSRCA-discussion] Controll Systems


    Found them.....http://www.horizonhobby.com/Products/Default.aspx?ProdID=KSJ1370    page 25 of the heli option parts and acc.....

    Rex
      ----- Original Message ----- 
      From: Rex LESHER<mailto:trexlesh at msn.com> 
      To: NSRCA Mailing List<mailto:nsrca-discussion at lists.nsrca.org> 
      Sent: Thursday, January 11, 2007 7:39 PM
      Subject: Re: [NSRCA-discussion] Controll Systems


      I'll look, I think I know where to get em....   If I find them, I'll put a link on the list...

      Rex
        ----- Original Message ----- 
        From: Ken Thompson<mailto:mrandmrst at comcast.net> 
        To: NSRCA Mailing List<mailto:nsrca-discussion at lists.nsrca.org> 
        Sent: Thursday, January 11, 2007 7:39 PM
        Subject: Re: [NSRCA-discussion] Controll Systems


        I think you are talking about the servo saver, I thought they quit making them...actually, I hope you're right, I can think of a few applications.
          ----- Original Message ----- 
          From: Rex LESHER<mailto:trexlesh at msn.com> 
          To: NSRCA Mailing List<mailto:nsrca-discussion at lists.nsrca.org> 
          Sent: Thursday, January 11, 2007 9:29 PM
          Subject: Re: [NSRCA-discussion] Controll Systems


          I believe they still have them, but now you have to find them in the Helicopter section....

          Rex
            ----- Original Message ----- 
            From: jivey61 at bellsouth.net<mailto:jivey61 at bellsouth.net> 
            To: NSRCA Mailing List<mailto:nsrca-discussion at lists.nsrca.org> 
            Sent: Thursday, January 11, 2007 7:22 PM
            Subject: Re: [NSRCA-discussion] Controll Systems


            Nat
             JR used to make a top bearing brace for the servos. It was a housing that went over the top of the servo and had a adjustable rod to the back of the servo connected to the brace.I use it on the rudder and it solves that problem of top bearing wear. Iv'e had the same problem before due to cable tension.
            We need to see if they are still available or get them to make them again.

            Jim Ivey
              ----- Original Message ----- 
              From: Nat Penton<mailto:natpenton at centurytel.net> 
              To: NSRCA Mailing List<mailto:nsrca-discussion at lists.nsrca.org> 
              Sent: Thursday, January 11, 2007 10:08 PM
              Subject: [NSRCA-discussion] Controll Systems


              I'm probably the originator of the .070 carbon-dep system - about 86. Carbon/balsa fuses and kevlar/balsa fuses , are poor combinations, and I'm still using them. Both systems are vulnerable to temp and/or humidity changes and are a pain. Since I've been doing this since 86 I must be a slow learner. No slop but sometimes a trim change every hour.

              With balsa fuses, for elev, I plan to go (back) to a balsa dowell pushrod and use a crossover ( MK, or custom ? ) just in front of the stab. Not sure how to handle the rudder, two small hard balsa dowells ? I've had undue kevlar tension ruin two DS8411sa servos on an electric.                              Nat


------------------------------------------------------------------


              _______________________________________________
              NSRCA-discussion mailing list
              NSRCA-discussion at lists.nsrca.org
              http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
            _______________________________________________
            NSRCA-discussion mailing list
            NSRCA-discussion at lists.nsrca.org
            http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


----------------------------------------------------------------------


          _______________________________________________
          NSRCA-discussion mailing list
          NSRCA-discussion at lists.nsrca.org
          http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
        _______________________________________________
        NSRCA-discussion mailing list
        NSRCA-discussion at lists.nsrca.org
        http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
      _______________________________________________
      NSRCA-discussion mailing list
      NSRCA-discussion at lists.nsrca.org
      http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


----------------------------------------------------------------------------


    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20070112/f2499be3/attachment.html