[NSRCA-discussion] low profile JR servo?

[Tony Stillman]

I don't know.

 

 

Tony Stillman, President

Radio South

3702 N. Pace Blvd

Pensacola, FL 32505

1-800-962-7802

www.radiosouthrc.com

 

  _____  

From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of J.Oddino
Sent: Thursday, February 22, 2007 6:08 PM
To: NSRCA Mailing List
Subject: Re: [NSRCA-discussion] low profile JR servo?

 

What is the resolution of the shaft encoder?

 

Jim

----- Original Message ----- 

From: Tony Stillman <mailto:tony at radiosouthrc.com>  

To: 'NSRCA Mailing List' <mailto:nsrca-discussion at lists.nsrca.org>  

Sent: Wednesday, February 21, 2007 8:28 AM

Subject: Re: [NSRCA-discussion] low profile JR servo?

 

Yes, it does.

 

 

Tony Stillman, President

Radio South

3702 N. Pace Blvd

Pensacola, FL 32505

1-800-962-7802

www.radiosouthrc.com

 


  _____  


From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Dean Pappas
Sent: Wednesday, February 21, 2007 10:03 AM
To: NSRCA Mailing List
Subject: Re: [NSRCA-discussion] low profile JR servo?

 

Hi Tony,

Does the throttle channel use the same encoder? If so, then it must be some
sort of absolute encoder.

Dean

 

Dean Pappas 
Sr. Design Engineer 
Kodeos Communications 
111 Corporate Blvd. 
South Plainfield, N.J. 07080 
(908) 222-7817 phone 
(908) 222-2392 fax 
d.pappas at kodeos.com 

-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org]On Behalf Of Tony Stillman
Sent: Wednesday, February 21, 2007 9:50 AM
To: 'NSRCA Mailing List'
Subject: Re: [NSRCA-discussion] low profile JR servo?

Gordon:
I am just passing along the info as the comment was made.  I have the
encoders in stock, as Futaba made a change in the production of the 14MZ and
sent me new ones to change out when needed.

 

 

Tony Stillman, President

Radio South

3702 N. Pace Blvd

Pensacola, FL 32505

1-800-962-7802

www.radiosouthrc.com

 


  _____  


From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Gordon
Anderson
Sent: Wednesday, February 21, 2007 8:40 AM
To: 'NSRCA Mailing List'
Subject: Re: [NSRCA-discussion] low profile JR servo?

 

The futaba 14MZ flyer I have says "Gimbals with long-life potentiometer,
quad bearings, adjustable tension and detent."

In general encoders are not absolute positioning devices and you need to
define "home". Resolvers are absolute positioning devices but larger and
more costly.

 

--Gordon

 


  _____  


From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Tony Stillman
Sent: Wednesday, February 21, 2007 5:46 AM
To: 'NSRCA Mailing List'
Subject: Re: [NSRCA-discussion] low profile JR servo?

The Futaba 14MZ uses shaft encoders on the sticks..

 

 

Tony Stillman, President

Radio South

3702 N. Pace Blvd

Pensacola, FL 32505

1-800-962-7802

www.radiosouthrc.com

 


  _____  


From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Bob Richards
Sent: Wednesday, February 21, 2007 7:18 AM
To: NSRCA Mailing List
Subject: Re: [NSRCA-discussion] low profile JR servo?

 

Hah, I didn't even think about the stick pots. Seems that would be the first
place they would try using shaft encoders.

 

Linear outputs from the servos would be great, also. Oh, wait a minute, that
was done 35 years ago with the KPS-11 servos. Nevermind....   :-)

 

Bob R.

Earl Haury <ehaury at houston.rr.com> wrote:

Isn't technology great - $2000+ TX and $100+ servos with everything riding
on a 50 cent pot on each end! 

 

Earl

----- Original Message ----- 

From: Bob Richards <mailto:bob at toprudder.com>  

To: NSRCA Mailing List <mailto:nsrca-discussion at lists.nsrca.org>  

Sent: Tuesday, February 20, 2007 8:37 PM

Subject: Re: [NSRCA-discussion] low profile JR servo?

 

When you say analog, I assume you are talking about the feedback loop? I
wonder how long it will be until we get shaft encoders in our servos. Or,
for that matter, the shaft encoder could be mounted to the control surface
itself.

 

Bob R.



"J.Oddino" <joddino at socal.rr.com> wrote:

Correct.  Well kind of.  Actually all of our servos are analog but you are
right, the super servos used the same principles as our modern "digital"
servos.

 

Jim O

----- Original Message ----- 

From: Bob Richards <mailto:bob at toprudder.com>  

To: NSRCA Mailing List <mailto:nsrca-discussion at lists.nsrca.org>  

Sent: Tuesday, February 20, 2007 1:22 PM

Subject: Re: [NSRCA-discussion] low profile JR servo?

 

I was under the impression that the "Super Servos" were actually first
generation digital servos. Is that not correct?

 

Bob R.



 


  _____  


_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

 


  _____  


_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 


  _____  


No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.441 / Virus Database: 268.18.3/694 - Release Date: 2/20/2007
1:44 PM

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20070223/26586e69/attachment-0001.html