[NSRCA-discussion] Monokote on Monokote

Lynn Burks rclen123 at adelphia.net
Thu Feb 22 20:22:47 AKST 2007


Hello Dave:  Yes i am going to the nats but going a different route this 
year.  This couple out here are starting to fly rc  and took some planes 
back to the nats for a few guys so this year they will take my  planes 
and I will fly the big silver bird to Iny and rent a car to go to 
Muncie.. They  have a big fifth wheel trailer and take 10 planes and we 
pay them a fee and they go on vacation so it works out for everyone.  
Next time i am in Oklahoma visiting I should drop down and visit ya.  Lynn

k6xyz wrote:
> Ok....I didn't know it was window cleaner.....I have plenty of windex
> though...heh.
> As long as it works better I'll get some...mebby I'll clean the windows
> too....or not!
>
> Hey...are you going to the NATS again?
> If so, mebby we can do it again and you can stay longer.
>
> Regards
>
> Dave Harmon
> NSRCA 586
> K6XYZ[at]sbcglobal[dot]net
> Sperry, Ok.
>
> -----Original Message-----
> From: nsrca-discussion-bounces at lists.nsrca.org
> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Lynn Burks
> Sent: Tuesday, February 20, 2007 11:09 PM
> To: NSRCA Mailing List
> Subject: Re: [NSRCA-discussion] Monokote on Monokote
>
> Hey old partner:  Yes Cinch a product of Proctor and Gamble ( window 
> cleaner) it seems to attach the monokote glue a little better.  Lynn
>
> k6xyz wrote:
>   
>> Hi Lynn....great to hear from you again!
>> I've never heard of that stuff but I'll keep it in mind.
>> Hopefully, the cold weather is done.....I've had enough of that for
>> awhile...a LONG while.
>>
>>
>> Regards
>>
>> Dave Harmon
>> NSRCA 586
>> K6XYZ[at]sbcglobal[dot]net
>> Sperry, Ok.
>>
>> -----Original Message-----
>> From: nsrca-discussion-bounces at lists.nsrca.org
>> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Lynn Burks
>> Sent: Monday, February 19, 2007 10:01 AM
>> To: NSRCA Mailing List
>> Subject: Re: [NSRCA-discussion] Monokote on Monokote
>>
>> Hey Dave: I have used Cinch ( in orange bottle) with good results. Is it 
>> warming up back there yet. Lynn
>>
>> k6xyz wrote:
>>   
>>     
>>> I have a bottle of some kind of liquid to attach MK over MK but I've 
>>> never tried it.
>>>
>>> Has anyone used it and how did you like it?
>>>
>>> Regards
>>>
>>> Dave Harmon
>>> NSRCA 586
>>> K6XYZ[at]sbcglobal[dot]net
>>> Sperry, Ok.
>>>
>>> -----Original Message-----
>>> *From:* nsrca-discussion-bounces at lists.nsrca.org 
>>> [mailto:nsrca-discussion-bounces at lists.nsrca.org] *On Behalf Of *Mark 
>>> Atwood
>>> *Sent:* Sunday, February 18, 2007 2:04 PM
>>> *To:* NSRCA Mailing List
>>> *Subject:* Re: [NSRCA-discussion] Monokote on Monokote
>>>
>>> Can it be too cold to build???
>>>
>>> Windex is definitely the best of those three. I've had very good 
>>> results with even semi large pieces (maybe 4" wide...anything wider 
>>> and I'll typically only do one layer). Don't skimp on the windex. Both 
>>> layers of monokote have to be clean...any dust will show up as a bump 
>>> under the film. I coat both the piece I'm putting down, as well as the 
>>> surface I'm putting it on, with a brush. Spraying it doesn't get 
>>> enough on (unless you go crazy) and just creates a million air bubbles 
>>> rather than a smooth film of liquid. I have it sloppy wet...then slide 
>>> the pieces into position, and I use a small 4" shower squeegee to 
>>> squeeze the windex out. You'll have zero bubbles...and it will adhere 
>>> from suction pretty aggressively. Yes...you'll have a wet mess so a 
>>> few paper towels are in order. Wait at least 24 hours and then use an 
>>> iron set just warm enough to anchor Monokote to Monokote without any 
>>> shrinking.
>>>
>>> If you heat it too soon (same day) there's enough moisture still 
>>> trapped between the two layers that you'll vaporize it and cause a 
>>> bazillion bubbles.
>>>
>>> -Mark
>>>
>>>
>>> On 2/18/07 12:55 PM, "Ed White" <edvwhite at sbcglobal.net> wrote:
>>>
>>> OK, Question for those finding it too cold to build. Is it possible to 
>>> put monokote on top of monokote and get decent results? Tried the poke 
>>> holes and windex/soap methods and not impressed with the results. Any 
>>> other ideas?
>>>
>>> Ed
>>>
>>> */ORLANDO FRETS <ojfrets at earthlink.net>/* wrote:
>>>
>>>
>>> Temperature in low 30's. It's cold! It's also too cold to build, shop 
>>> is cold. Stay inside where it's warm.
>>>
>>>
>>>
>>>
>>> ORLANDO FRETS
>>>
>>> ojfrets at earthlink.net
>>>
>>> ------------------------------------------------------------------------
>>>
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>
>>> ------------------------------------------------------------------------
>>>
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>     
>>>       
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>
>>   
>>     
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
>   


More information about the NSRCA-discussion mailing list