[NSRCA-discussion] interference/power failure

Ron Lockhart ronlock at comcast.net
Mon Feb 19 16:04:55 AKST 2007


I prefer minimum metal parallel to antenna.  So I use kevlar pull-pull cables.  That said, this 
description of behavior isn't typical of the erratic behavior of a PPM receiver being hit by 
interference from parallel metal, external RF or whatever.  
The behavior you describe is certainly consistent with power failure.   Battery, switch, or connectors
in that path.  A possible response is two batteries, thru two switches, with two lines to RX.

Later,  Ron Lockhart
  ----- Original Message ----- 
  From: jfgreen 
  To: 'NSRCA Mailing List' 
  Sent: Monday, February 19, 2007 7:43 PM
  Subject: Re: [NSRCA-discussion] interference


  Keith,  No need to have used a hammer on that RX it was obliterated when I scooped the two garbage bags full of debris.  I immediately sent the JR 10X to Tony and ordered a dual conversion RX w/ full explanation of the event.  Jaccio switch, parsons clips and a two year old Duralite battery.  Not glitch before the crash.  It acted like a battery died.  Went into first loop of Cuban eight.  Loop opened up (blowback) slow rolled over and dove in.  No control on sticks, throttle stayed where it was at beginning of maneuver.  THX Jerry

   


------------------------------------------------------------------------------

  From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Keith Black
  Sent: Monday, February 19, 2007 4:27 PM
  To: NSRCA Mailing List
  Subject: Re: [NSRCA-discussion] interference

   

  Jerry,

   

  I've personally had no problem with steel pull-pull cables, however, I've also been careful to keep the antenna away from the pull-pull cables by several inches.

   

  Do you understand what occurred with your last incident?  I've heard of people losing  their replacement plane because they didn't realize they had either a bad TX or bad RX and they used them in the replacement plane. Therefore, if I were you I'd focus on making 100% SURE that none of the components used before (that you plan to use again, including TX) are faulty. 

   

  I'm not quite this hard core, but Earl Haury once told me that when he has a crash he takes the RX home and introduces it to his hammer. This would certainly prevent any problems with the RX (either causing the crash or caused by the crash) from downing any future planes. 

   

  Keith Black

    ----- Original Message ----- 

    From: jfgreen 

    To: 'NSRCA Mailing List' 

    Sent: Monday, February 19, 2007 5:46 PM

    Subject: [NSRCA-discussion] interference

     

    In an effort to avoid turning my new pattern ship into a dirt seeking comet similar to my last Oly, I’ve been researching some possible causes,  I recently read from one source that one would or could have interference problems if when using steel pull-pull cables and installing the antenna parallel to them inside the fuse.  I have seen a number of AC at contests w/this configuration that seem to have no interference problems.  Your  experience, thoughts please.  THX - Jerry

     

     

    --
    No virus found in this outgoing message.
    Checked by AVG Free Edition.
    Version: 7.1.412 / Virus Database: 268.18.3/693 - Release Date: 2/19/2007


----------------------------------------------------------------------------

    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion



  --
  No virus found in this incoming message.
  Checked by AVG Free Edition.
  Version: 7.1.412 / Virus Database: 268.18.3/693 - Release Date: 2/19/2007





  --
  No virus found in this outgoing message.
  Checked by AVG Free Edition.
  Version: 7.1.412 / Virus Database: 268.18.3/693 - Release Date: 2/19/2007




------------------------------------------------------------------------------


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20070220/4b5cf288/attachment.html 


More information about the NSRCA-discussion mailing list