[NSRCA-discussion] Monokote on Monokote

[george w. kennie]

Re: [NSRCA-discussion] Monokote on MonokoteYeah Dave,
Me too. Another thing that you can't do with the new formulation is make it stick to Concept paint. Bummer !
G.


  ----- Original Message ----- 
  From: k6xyz 
  To: 'NSRCA Mailing List' 
  Sent: Sunday, February 18, 2007 5:44 PM
  Subject: Re: [NSRCA-discussion] Monokote on Monokote


  Just curious George...I'm probably gonna use UK next time.

  I started having trouble with MK in 2000 or 2001..now it won't work at all for me.

  Too bad..it was great stuff.



  Regards

  Dave Harmon
  NSRCA 586
  K6XYZ[at]sbcglobal[dot]net
  Sperry, Ok. 

  -----Original Message-----
  From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of george w. kennie
  Sent: Sunday, February 18, 2007 4:36 PM
  To: NSRCA Mailing List
  Subject: Re: [NSRCA-discussion] Monokote on Monokote



  Yup, used it b/4 the new formulation and it makes for a very strong bond, but you only get one chance to get the position right. Once it's down, it ain't coming up.

  G.

    ----- Original Message ----- 

    From: k6xyz 

    To: 'NSRCA Mailing List' 

    Sent: Sunday, February 18, 2007 4:12 PM

    Subject: Re: [NSRCA-discussion] Monokote on Monokote



    I have a bottle of some kind of liquid to attach MK over MK but I've never tried it.

    Has anyone used it and how did you like it?



    Regards

    Dave Harmon
    NSRCA 586
    K6XYZ[at]sbcglobal[dot]net
    Sperry, Ok. 

    -----Original Message-----
    From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Mark Atwood
    Sent: Sunday, February 18, 2007 2:04 PM
    To: NSRCA Mailing List
    Subject: Re: [NSRCA-discussion] Monokote on Monokote



    Can it be too cold to build???

    Windex is definitely the best of those three.  I've had very good results with even semi large pieces (maybe 4" wide...anything wider and I'll typically only do one layer).  Don't skimp on the windex.  Both layers of monokote have to be clean...any dust will show up as a bump under the film.  I coat both the piece I'm putting down, as well as the surface I'm putting it on, with a brush.  Spraying it doesn't get enough on (unless you go crazy) and just creates a million air bubbles rather than a smooth film of liquid.  I have it sloppy wet...then slide the pieces into position, and I use a small 4" shower squeegee to squeeze the windex out.  You'll have zero bubbles...and it will adhere from suction pretty aggressively.  Yes...you'll have a wet mess so a few paper towels are in order.   Wait at least 24 hours and then use an iron set just warm enough to anchor Monokote to Monokote without any shrinking.

    If you heat it too soon (same day) there's enough moisture still trapped between the two layers that you'll vaporize it and cause a bazillion bubbles.  

    -Mark 


    On 2/18/07 12:55 PM, "Ed White" <edvwhite at sbcglobal.net> wrote:

    OK, Question for those finding it too cold to build.  Is it possible to put monokote on top of monokote and get decent results?  Tried the poke holes and windex/soap methods and not impressed with the results.  Any other ideas?

    Ed

    ORLANDO FRETS <ojfrets at earthlink.net> wrote:

           
    Temperature in low 30's. It's cold! It's also too cold to build, shop is cold. Stay inside where it's warm.
     
     
     
     
    ORLANDO FRETS
     
    ojfrets at earthlink.net
     
     




----------------------------------------------------------------------------

    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion




----------------------------------------------------------------------------

    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion



------------------------------------------------------------------------------


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20070219/12075c49/attachment.html