[NSRCA-discussion] cleaning up an engine ?

[Pete Cosky]

I have a small gear puller that works great for pulling thrust washers. I 
think Central sells one as well.

As for cleaning an engine I have had great luck with the old crock pot full 
of antifreeze technique. I doubt it would remove rust but it sure does clean 
up baked on glow goo.


----- Original Message ----- 
From: "Paul Horan" <paul.horan at sbcglobal.net>
To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
Sent: Tuesday, October 03, 2006 11:22
Subject: Re: [NSRCA-discussion] cleaning up an engine ?


> John,
>    Until I get some Demon Clean do you have any other alternatives to 
> cleaning up the engine ?
>    How about getting the woodruff key out ?  Should the oven @ 300 work.
> Thanks
> Paul
> ----- Original Message ----- 
> From: "John Pavlick" <jpavlick at idseng.com>
> To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
> Sent: Monday, October 02, 2006 11:49 PM
> Subject: Re: [NSRCA-discussion] cleaning up an engine ?
>
>
>>I use this stuff called "Demon Clean" and it works great. I tried oven
>> cleaner, barbecue grill cleaner, etc. Some of these discolored the 
>> aluminum
>> if you left it on too long. The Demon Clean has proven to be very 
>> effective
>> and a little goes a long way. One can will probably last a few years so 
>> it's
>> really not expensive. You can buy it here:
>> http://www.bj-model-engines.com/Demon-Clean_email_response_11-11-05.html
>>
>> John Pavlick
>> http://www.idseng.com
>>
>>
>>> -----Original Message-----
>>> From: nsrca-discussion-bounces at lists.nsrca.org
>>> [mailto:nsrca-discussion-bounces at lists.nsrca.org]On Behalf Of Paul Horan
>>> Sent: Tuesday, October 03, 2006 12:31 AM
>>> To: nsrca-discussion at lists.nsrca.org
>>> Subject: [NSRCA-discussion] cleaning up an engine ?
>>>
>>>
>>>     I am working on changing the bearing on an OS BXI.  It was
>>> ran hard and put away wet.  Varnish carbon and some rust.
>>>
>>>     Also how do I get the woodruff pin out of the thrust washer ?
>>>   My plan so far is to heat the engine up to about 300 f in the
>>> oven and try to pop the thrust washer off.
>>>
>>> Thanks,
>>> Paul
>>>
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>> --
>>> No virus found in this incoming message.
>>> Checked by AVG Free Edition.
>>> Version: 7.1.407 / Virus Database: 268.12.12/461 - Release Date: 10/2/06
>>>
>> --
>> No virus found in this outgoing message.
>> Checked by AVG Free Edition.
>> Version: 7.1.407 / Virus Database: 268.12.12/461 - Release Date: 10/2/06
>>
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>