[NSRCA-discussion] APC 18.1 x 10W props

[k6xyz]

Naaaa...he makes everyone else look short.well.mebby not Cunningham!

 

Regards

Dave Harmon
NSRCA 586
K6XYZ[at]sbcglobal[dot]net
Sperry, Ok. 

-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of wgalligan
Sent: Wednesday, November 15, 2006 5:17 PM
To: NSRCA Mailing List
Subject: Re: [NSRCA-discussion] APC 18.1 x 10W props

 

I though it was the fat prop that made him look so thin.

 

Wayno

----- Original Message ----- 

From: Richard Strickland <mailto:richard.s at allied-callaway.com>  

To: 'NSRCA Mailing List' <mailto:nsrca-discussion at lists.nsrca.org>  

Sent: Wednesday, November 15, 2006 5:15 PM

Subject: Re: [NSRCA-discussion] APC 18.1 x 10W props

 

Don't get your picture taken with Harrison--he makes everyone else look fat.
Hi Mike!

 

Richard

-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org]On Behalf Of Dr. Mike
Harrison
Sent: Wednesday, November 15, 2006 4:26 PM
To: NSRCA Mailing List
Subject: Re: [NSRCA-discussion] APC 18.1 x 10W props

Yeah, Yeah, Yeah.......

 

----- Original Message ----- 

From: Gray E Fowler <mailto:gfowler at raytheon.com>  

To: NSRCA Mailing List <mailto:nsrca-discussion at lists.nsrca.org>  

Sent: Wednesday, November 15, 2006 2:49 PM

Subject: Re: [NSRCA-discussion] APC 18.1 x 10W props

 


Good God almighty! Mike Harrison on the list! Can Art Wagner be far behind? 



Gray Fowler
Senior Principal Chemical Engineer
Radome and Composites Engineering
Raytheon 

nsrca-discussion-bounces at lists.nsrca.org wrote on 11/15/2006 02:41:42 PM:

> Thanks George! 
> ----- Original Message ----- 
> From: george w. kennie 
> To: NSRCA Mailing List 
> Sent: Wednesday, November 15, 2006 12:03 PM 
> Subject: Re: [NSRCA-discussion] APC 18.1 x 10W props 
> 
> Welcome to the list Mike!!!!! 
> ----- Original Message ----- 
> From: Dr. Mike Harrison 
> To: NSRCA Mailing List 
> Sent: Wednesday, November 15, 2006 8:31 AM 
> Subject: Re: [NSRCA-discussion] APC 18.1 x 10W props 
> 
> Peter, 
> Hi, 
> I am Mike Harrison, I worked with APC to develop these props.  Let 
> me tell you the goal of the prop design.  It is to fly at a moderate
> to slow constant speed under the noise limit but with good pulling 
> performance.  Therefore, regarding the rpm, the 8000 is about ideal 
> for that prop, turn it much more and you will be above the noise limit.   
>   
> I find it interesting that you determine whether a prop is adequate 
> by first tacking it.  I would think you would fly it first to see if
> it was adequate.  I would encourage you to do that first.  The OS 
> 140 turns it about the same and it flies very well. 
>   
> The whole purpose was to develop a prop that would fly at a 
> deliberate pace at about 150 meters to compete with the electrics.   
>   
> There is also an 18.5x9.5 which I fly and it turns about 7500 rpm.  
> I like it better than the 18.1x10.  I am working on a 19x9 at the moment. 
>   
> Good luck 
> Mike 
> From: Peter Pennisi 
> To: 'NSRCA Mailing List' 
> Sent: Tuesday, November 14, 2006 5:48 PM 
> Subject: [NSRCA-discussion] APC 18.1 x 10W props 
> 
>   
> I recently purchased some 18.1 x 10W APC props for my DZ160. 
> Apparently there appears to be another version 18.1 x 10.1. 
>   
> Could someone please tell me the difference between both? 
>   
> I tried a quick ground run on this prop (stock) this morning but 
> could barely get 8000 RPM from the engine. I will take advice from a
> member on this list and lop 1/4inch of each blade. What RPM readings
> are people getting who are using either of these props on a YS DZ160
engine? 
>   
>   
> Regards, 
>   
> Peter 
> 
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
> 
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
> 
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 


  _____  


_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


  _____  


_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20061116/4355ba99/attachment.html