[NSRCA-discussion] Help: Servo pins pulled out of connector body

[mike mueller]

 Where do you buy the proper crimpers? Mike

John Ferrell <johnferrell at earthlink.net> wrote:      I disagree with soldering a crimp. If done properly the crimped connection ALONE is the most reliable and durable connection.
   
  John Ferrell    
http://DixieNC.US

    ----- Original Message ----- 
  From: Dennis Bodary 
  To: NSRCA Mailing List 
  Sent: Saturday, March 18, 2006 2:28 AM
  Subject: Re: [NSRCA-discussion] Help: Servo pins pulled out of connector body
  

Servo city sells the pins and the connectors for 75 cents to like 2 bucks depending on which ones you want. The crimpers will probably cost you 25 bucks. they are a w crimp. you do not want to use regular crimpers. After you crimp them you will want to solder also. use the smallest diameter solder you can find. you just need a tiny tiny amount. you won't be able to use heat shrink due to the heat shrink not fitting in the connector.

paul <paul.horan at sbcglobal.net> wrote:           Ed,
      I have not pulled the servos apart to check the gears.  The reason I think they are ok is that when the plane went in the engine was dead, the speed was fairly low, the the smaller branches of the tree furthe! r reduced the speed and finally the plane hit a fork that cleanly stripped the wings away.  The servos, ailerons, linkage all looked good.  
  Thanks,
  Paul
    ----- Original Message ----- 
  From: Ed Alt 
  To: NSRCA Mailing List 
  Sent: Monday, March 13, 2006 9:38 PM
  Subject: Re: [NSRCA-discussion] Help: Servo pins pulled out of connector body
  
  Paul:
  The soldering trick works fine, as long as you don't get a cold joint.  I try to avoid it only because the area near where the solder stops wicking into the wire tends to be a point of stress concentration for the wire strands, but as long as you extend the heat shrink about 1/4" past the point where the wire gets 'bendy' again, it supports it and prevents the work hardening of the wire from becoming a problem.  I might be a bit nervous about those servos though - how do the gears look?  I've had incidents where just a tiny sliver of a gear tooth was chipped away and lead to further problems.
   
  Ed
    ----- Original Message ---! -- 
  From: paul 
  To: NSRCA Mailing List 
  Sent: Monday, March 13, 2006 10:29 PM
  Subject: Re: [NSRCA-discussion] Help: Servo pins pulled out of connector body
  

  Ed,
      Sounds like I can either get the kit and crimper from Maxx or cut the connector ends off defunct servos / extentions and solder them to the existing servo wires - using heat shrink to keep any flexing away from the solder joints.  Any preference ?
  Thanks,
  Paul
    ----- Original Message ----- 
  From: Ed Alt 
  To: NSRCA Mailing List 
  Sent: Monday, March 13, 2006 9:24 PM
  Subject: Re: [NSRCA-discussion] Help: Servo pins pulled out of connector body
  

  Paul:
  Better off to replace the entire connector and pins.  Most likely the plastic housing was damaged from the pin pulling out.  Also, the! wire had to get strained where it is clasped by the crimp pins.  Maxx Products sells connector kits, but you need a crimper tool.  
   
  Ed
   
  ----- Original Message ----- 
    From: paul 
  To: NSRCA Mailing List 
  Sent: Monday, March 13, 2006 10:13 PM
  Subject: [NSRCA-discussion] Help: Servo pins pulled out of connector body
  

    I strained my Meridian through a tree, wrecked the plane but the equipment appears OK with the exception of both aileron servos.  When the wings came off the servo connector body stayed in the fuse and the servos wires and pins went with the wings.  
      My question is : can I simply re-insert the servo pins in another connector body (taken from defuct servos or extentions) ?
  Thanks,
  Paul
    
---------------------------------
    
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
    
---------------------------------
    
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
    
---------------------------------
    
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion       
---------------------------------
    
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion   _______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion   
    
---------------------------------
  Yahoo! Travel
Find great deals to the top 10 hottest destinations!     
---------------------------------
    
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

		
---------------------------------
 Yahoo! Mail
 Use Photomail to share photos without annoying attachments.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20060318/aa74ecbc/attachment-0001.html