[NSRCA-discussion] Futaba ZAP WC2 transmitter problem

Peter Pennisi pentagon.systems at bigpond.com
Mon Jan 2 19:40:33 AKST 2006


Hi Karl,

Great to hear from you again. I wouldn't mind your weather at the moment. It
is so hot down here that you can't stay outside let alone fly.

I have checked the loom and all is OK in that department. It appears that
the pot may be rotating so I am investigating this theory.

Cheers,

Peter




Peter Pennisi
 
Pentagon Systems QLD Pty Ltd
P.O Box 4280
Eight Mile Plains
QLD 4113
Australia
Phone:    61+0738414234
Fax:        61+0738414264
Mobile:   0408007206
Email: pentagon.systems at bigpond.com

-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Karl G.
Mueller
Sent: Tuesday, 3 January 2006 12:54 PM
To: NSRCA Mailing List
Subject: Re: [NSRCA-discussion] Futaba ZAP WC2 transmitter problem

  Peter,

  Hope every body is well down under.
  I had a similar problem where the servo would jump at the very end of
  the stick travel. All it was that the loop in the wires from the pot was
  to tight and at the end of the travel would put some strain on the pot
  connections. I increased the amount of the slack in the wires and
  that fixed the problem. Don't know whether that might be your problem
  as well or not.

  Karl G. Mueller
  kgamueller at rogers.com


  ----- Original Message ----- 
  From: "Peter Pennisi" <pentagon.systems at bigpond.com>
  To: "'NSRCA Mailing List'" <nsrca-discussion at lists.nsrca.org>
  Sent: Monday, January 02, 2006 6:46 PM
  Subject: RE: [NSRCA-discussion] Futaba ZAP WC2 transmitter problem


  > Yes it does.
  >
  >
  >
  >
  > Peter Pennisi
  >
  > Pentagon Systems QLD Pty Ltd
  > P.O Box 4280
  > Eight Mile Plains
  > QLD 4113
  > Australia
  > Phone: 61+0738414234
  > Fax: 61+0738414264
  > Mobile: 0408007206
  > Email: pentagon.systems at bigpond.com
  > ________________________________________
  > From: nsrca-discussion-bounces at lists.nsrca.org
  > [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of brian
young
  > Sent: Tuesday, 3 January 2006 9:33 AM
  > To: NSRCA Mailing List
  > Subject: Re: [NSRCA-discussion] Futaba ZAP WC2 transmitter problem
  >
  > Does this show up in the Servo display, the screen that shows servo
motion?
  > Seems like it should.
  >
  > Brian
  >
  > Peter Pennisi <pentagon.systems at bigpond.com> wrote:
  > Hi all,
  >
  > My transmitter has recently developed a weird problem and only seems to
be
  > affected on the elevator channel (Mode 1)
  >
  > What happens is when I move the elevator gimbals to approximately 95%
down
  > elevator the servo will reverse to up elevator.
  >
  > I have checked all my mixes and programming and can confirm this is not
the
  > problem area. I have also checked all my flight systems and the problem
is
  > not there.
  >
  > I have cross checked everything and the consensus leads to a problem in
the
  > transmitter. My new model has dual elevator servo's and the problem
causes
  > both servo's to reverse so that
  > Confirms the probl! em is in the transmitter.
  >
  > The problem is evident on all 6 models programmed in my transmitter.
  >
  > I initially thought the problem was a faulty or dirty elevator pot but
some
  > tests I recently carried out don't convince me this is the problem. My
  > suspicions are that I may have a cable problem somewhere between
  > The elevator pot and the main processor board so I have since ordered a
  > replacement set of ribbon cables.
  >
  > I know most of you are asking yourself why not send the radio in to a
proper
  > service centre. We just don't have people in Australia that I trust
enough
  > to carry out any work with Futaba systems. I guess if all else fails
  > I will send it to Japan at great cost.
  >
  > Anyway I recently became aware of another local WC2 transmitter which
has
  > exactly the same problem as mine. Now I am starting to think that this
may
  > be a common problem. Has anyone else on this mailing list ever
experienced
  > a similar problem?
  >
  >
  > Regards,
  >
  > Peter
  >
  >
  >
  > _______________________________________________
  > NSRCA-discussion mailing list
  > NSRCA-discussion at lists.nsrca.org
  > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
  >
  > ________________________________________
  > Yahoo! Shopping
  > Find Great Deals on Holiday Gifts at Yahoo! Shopping
  >
  >
  >
  > _______________________________________________
  > NSRCA-discussion mailing list
  > NSRCA-discussion at lists.nsrca.org
  > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


----------------------------------------------------------------------------
----


_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion




More information about the NSRCA-discussion mailing list