[NSRCA-discussion] Trim changes

[Ed Alt]

You might want to check out the Prestige thread under Pattern on RCU.  I adopted a pushrod method that Dave Lockhart has used for some time and there are some pics and description there.  I think Dave's installation method is more highly evolved than what I patched together, but I think what's shown in the thread is a reasonable facsimili.  When you first hear about using Nyrods, you will most likely be very skeptical.  I sure was.  These are different though, since they have the CF slider vs. the usual junk.  There is some change with temperature, but not nearly as much as I have experienced with other methods.  It's really light, really cheap and not too difficult to install.  It's also a very positive control feel.

Ed
  ----- Original Message ----- 
  From: Nat Penton 
  To: NSRCA Mailing List 
  Sent: Wednesday, December 06, 2006 11:27 PM
  Subject: Re: [NSRCA-discussion] Trim changes


  Amir
  All that fine weather is bad for relations !

  I use Kevlar pull-pull on rudder, balsa fuse, and with high humidity I am worried the servo will be uprooted. Need to adjust atleast daily. Also use DEP on elev ( 20 years ) and have trim changes sometimes hourly. I need to change both.            Nat
    ----- Original Message ----- 
    From: Amir Neshati 
    To: 'NSRCA Mailing List' 
    Sent: Wednesday, December 06, 2006 2:21 PM
    Subject: Re: [NSRCA-discussion] Trim changes


    I thought it went like, "wood fuse, pull-pull, fiberglass fuse, pull-pull, carbon fuse, pull-pull." Lightest set up too.

    65 degrees, sunny, calm, clear & comfortable....

    Amir



----------------------------------------------------------------------------
    From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Dean Pappas
    Sent: Wednesday, December 06, 2006 11:25 AM
    To: NSRCA Mailing List
    Subject: Re: [NSRCA-discussion] Trim changes


    Hi All,
    Back in the Stone Age (Ron remembers this) we always said, "wood fuse, wood pushrod and fiberglass fuse, fiberglass pushrod.
    As long as the elevator trim is the only one that changes, then life is simple especially with crossed digital trims.
    Putting the servos in the tail works, as does an MS-10 or Matchbox.
    So does putting a 1:1 bellcrank halfway between the servo arm and the elevator horn. That's a trick that nobody uses anymore.

    Dean

    Dean Pappas 
    Sr. Design Engineer 
    Kodeos Communications 
    111 Corporate Blvd. 
    South Plainfield, N.J. 07080 
    (908) 222-7817 phone 
    (908) 222-2392 fax 
    d.pappas at kodeos.com 

      -----Original Message-----
      From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org]On Behalf Of Jay Marshall
      Sent: Wednesday, December 06, 2006 2:06 PM
      To: 'NSRCA Mailing List'
      Subject: Re: [NSRCA-discussion] Trim changes


      Some servo electronics could be temp sensitive. Measure the elevator on a cold morning then warm it up slowly with a heat gun (carefully) and see if anything moves.

       

      -----Original Message-----
      From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Brian Billings
      Sent: Wednesday, December 06, 2006 12:05 PM
      To: nsrca-discussion at lists.nsrca.org
      Subject: [NSRCA-discussion] Trim changes

       

      I have been dealing with elevator trim changes on my D.E.P.S. installation which has been worse with cold mornings and warm afternoons. Last night on the way home from the field I got the idea of figuring out a way to take the pot out of the servo and mounting it on the control surface, that way the surface will always go to it's set position regardless of how much the fuse has expanded or contracted. Anybody ever try this, I know it could be done but is it practical? My worry is vibration, sealing the pot from the elements, oil, keeping a clean signal with the long leads to the rear and a positive connection from pot to surface. Is this a dumb Idea?

       

      Brian  



----------------------------------------------------------------------------


    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 


----------------------------------------------------------------------------


    Internal Virus Database is out-of-date.
    Checked by AVG Free Edition.
    Version: 7.1.409 / Virus Database: 268.13.20/508 - Release Date: 10/31/2006



------------------------------------------------------------------------------


  Internal Virus Database is out-of-date.
  Checked by AVG Free Edition.
  Version: 7.1.409 / Virus Database: 268.13.20/508 - Release Date: 10/31/2006




------------------------------------------------------------------------------


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20061207/d8044e49/attachment.html