[NSRCA-discussion] Robart air can leak

[Dennis Bodary]

Ken you should be practicing not drinking Bud Light and playing with hubble bubble. it does'nt work right with Bud light you need Busch Beer. Look out i've got three flights on the Focus since October. I think if i get some more practice i can finish last in advanced this year.
   
  Dennis

Ken Thompson <mrandmrst at comcast.net> wrote:
  Hey Del,

I thought about that, but the material is so thin I'll warp the can trying 
to come up to temp for the brazing rod. I found out a replacement can is 
only 10.00, not worth the effort to fix the old one.
----- Original Message ----- 
From: "Del K. Rykert" 
To: "NSRCA Mailing List" 
Sent: Sunday, April 30, 2006 8:46 AM
Subject: Re: [NSRCA-discussion] Robart air can leak


> Depending on how thick the material might be able to braze?
>
> Del
>
> ----- Original Message ----- 
> From: "Jay Marshall" 

> To: "'NSRCA Mailing List'" 
> Sent: Sunday, April 30, 2006 8:39 AM
> Subject: Re: [NSRCA-discussion] Robart air can leak
>
>
>> Solder won't work for sure - you can't solder AL.
>>
>> -----Original Message-----
>> From: nsrca-discussion-bounces at lists.nsrca.org
>> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Bob Kane
>> Sent: Sunday, April 30, 2006 8:08 AM
>> To: NSRCA Mailing List
>> Subject: Re: [NSRCA-discussion] Robart air can leak
>>
>> That's what I thought, solder is not going to work.
>> Try the JB Weld, or the special bubble gum Mike
>> mentioned ;)
>>
>> --- Ken Thompson wrote:
>>
>>> It's made of aluminum, I've already scuffed the
>>> area, I will get the JB for
>>> aluminum and try it out. I'll just test it out real
>>> good before I
>>> re-install it.
>>>
>>> I also got a hint of using Hubba Bubba bubble gum,
>>> that sounds like a tasty
>>> attempt also.
>>>
>>> Ken
>>> ----- Original Message ----- 
>>> From: "Bob Kane" 
>>> To: "NSRCA Mailing List"
>>> 
>>> Sent: Saturday, April 29, 2006 9:36 PM
>>> Subject: Re: [NSRCA-discussion] Robart air can leak
>>>
>>>
>>> > What is the can made of? I think JB Weld would
>>> work
>>> > if you get the area clean.
>>> >
>>> > --- Ken Thompson wrote:
>>> >
>>> >> Does anybody have any clue how I can repair a
>>> >> pinhole leak in a Robart air cylinder?
>>> >>
>>> >> For some reason there is a tiny leak in the side
>>> of
>>> >> the can. Solder and silver solder won't hold
>>> >> pressure. I thought about JB weld for aluminum,
>>> but
>>> >> I'm not sure that will hold 80 to 100 PSI either.
>>> >>
>>> >> Any hints would be helpful, TIA.
>>> >>
>>> >> Ken>
>>> _______________________________________________
>>> >> NSRCA-discussion mailing list
>>> >> NSRCA-discussion at lists.nsrca.org
>>> >>
>>> >
>>>
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>> >
>>> >
>>> > Bob Kane
>>> > getterflash at yahoo.com
>>> >
>>> > __________________________________________________
>>> > Do You Yahoo!?
>>> > Tired of spam? Yahoo! Mail has the best spam
>>> protection around
>>> > http://mail.yahoo.com
>>> > _______________________________________________
>>> > NSRCA-discussion mailing list
>>> > NSRCA-discussion at lists.nsrca.org
>>> >
>>>
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>
>>>
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>>
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>
>>
>>
>> Bob Kane
>> getterflash at yahoo.com
>>
>> __________________________________________________
>> Do You Yahoo!?
>> Tired of spam? Yahoo! Mail has the best spam protection around
>> http://mail.yahoo.com
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>
>>
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


		
---------------------------------
Blab-away for as little as 1¢/min. Make  PC-to-Phone Calls using Yahoo! Messenger with Voice.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20060430/215acdf0/attachment.html