[SPAM] Re: OS 160 pump backplate

[Randy]

Thanks Eric.  OS160 is still a great engine even if you need to add a reg/pump and 3 blade prop selection is limited.

Randy

----- Original Message ----- 
  From: Grow Pattern 
  To: Discussion 
  Sent: Friday, September 30, 2005 11:36 PM
  Subject: Re: OS 160 pump backplate


  Before you all leap out and spend a bunch of money on an OS pump for your OS 1.60 here is what I found out while experimenting with the OS 1.60's.

  First of all, you cannot buy the pump separately. It comes installed on the 1.40 back plate.approx $150.

  Secondly, the standard OS 1.60 carb did not like the OS pump anywhere near as much as it liked the Cline regulator. (Other 1.60 users swear by the Perry). Either way the OS pump produced too much fuel for the OS 1.60 carb.

  I spent a lot of time working on the pump in the backplate with the std carb. Tried twin pug heads etc. Still could not get a good transition. If I leaned the pump for  a good transition then the engine would go lean in the verticals. I finally had enough of this and went to the OS mix carb (the one that is sadly not available). 

  You, (or at least I, could not) cannot get the std carb to work well with a pipe when the fuel is supplied from an OS 1.40 pump. I did get it to work well with a 1.40 RX carb. This carb is designed for the pump but needs to be drilled and tapped to take 3.5-mm screws to hold it in place.

  The Cline will get you much better results for around $40. (Or Perry if you prefer) and you can use your existing.

  Regards,

  Eric.




  ----- Original Message ----- 
    From: Koenig, Tom 
    To: Discussion 
    Sent: Thursday, September 29, 2005 6:28 PM
    Subject: OS 160 pump backplate


    Gentlemen

    Yes, he does make them available to those that want them. They are machined from billet stock, you will however have to supply your own pump. I think Tower has them at a reasonable price? There are no carby mods neccessary. I have mentioned this about two years ago, maybe thats where Eric got the idea? 

    If people would like one, I believe he charges about $100 AUS for them, that works out about 75 US. Not cheap-but speaking as a YS man-even I have to say his set up is sweet.

    If anyone wants his details, contact me off-line and I will provide you with his e-mail address- so you can speak to the man himself. I am actually doing a section in my column in our next APA newsletter on his set-up.

    Tom
      -----Original Message-----
      From: RUDDERCABL at aol.com [mailto:RUDDERCABL at aol.com]
      Sent: Thursday, 29 September 2005 11:52 PM
      To: Koenig, Tom
      Cc: discussion at nsrca.org
      Subject: Re: Iron Bay Regulator


      In a message dated 9/28/2005 11:36:19 PM Eastern Standard Time, Tom.Koenig at actewagl.com.au writes:
        Wayne- a pattern buddy of mine CNC's backplates for the OS 160 to suit the OS pump unit. His has run faultlessly for years ( apart from bearings ie: the usual maintenance).

        Dunno why OS themselves has not done so either.

        Tom

      Tom 

      Does he make them to sell? If so, where and how can I purchase one. Eric Henderson has that set-up and it is really sweet.

      Robert Gainey
          ************************************************************************
          *PLEASE NOTE* This email and any attachments may
          be confidential. If received in error, please delete all 
          copies and advise the sender. The reproduction or 
          dissemination of this email or its attachments is 
          prohibited without the consent of the sender.

          WARNING RE VIRUSES: Our computer systems sweep
          outgoing email to guard against viruses, but no warranty 
          is given that this email or its attachments are virus free. 
          Before opening or using attachments, please check for 
          viruses. Our liability is limited to the re-supply of any 
          affected attachments.

          Any views expressed in this message are those of the 
          individual sender, except where the sender expressly,
          and with authority, states them to be the views of the 
          organisation.
          ************************************************************************
         
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.f3a.us/pipermail/nsrca-discussion/attachments/20051001/e355751a/attachment-0001.html