[SPAM] Re: [SPAM] Re: JR output arm stabilizers

[Ed Alt]

Yes, it's about 3 or 4 bucks.  However, you leave the metal output gear in place and go nylon with the rest.  
  ----- Original Message ----- 
  From: Dave Burton 
  To: discussion at nsrca.org 
  Sent: Wednesday, November 23, 2005 12:35 PM
  Subject: RE: [SPAM] Re: JR output arm stabilizers


  Can one convert the 8411 to 8411SA by replacing the metal gears with a plastic gear set?
    -----Original Message-----
    From: discussion-request at nsrca.org [mailto:discussion-request at nsrca.org]On Behalf Of Ed Alt
    Sent: Wednesday, November 23, 2005 12:22 PM
    To: discussion at nsrca.org
    Subject: [SPAM] Re: JR output arm stabilizers


    Yep, the 8611or better yet, the 8611A is another good way to go, though I am using up available inventory of 8411's.  BTW, 8411's can often be had at a bargain price, since they have fallen out of favor which much of the big gas crowd.  They're a very good servo for Pattern use once converted to SA.  A major complaint in big gas use was that the metal gears wore very quickly, which often contributed the the other big complaint that they would oscillate.  There used to be lots of fun discussions about how to set things up to make that stop happening.

    Ed
      ----- Original Message ----- 
      From: Wayne Galligan 
      To: discussion at nsrca.org 
      Sent: Wednesday, November 23, 2005 12:13 PM
      Subject: Re: JR output arm stabilizers


      Just put an 8611 in there and no worries.

      I got one these and am going to try it on the rudder of my new ship.    Can you say OVERKILL??

      WG


        ----- Original Message ----- 
        From: humptybump at comcast.net 
        To: discussion at nsrca.org 
        Sent: Wednesday, November 23, 2005 10:58 AM
        Subject: Re: JR output arm stabilizers


        It does help in high stress applications. I use them on the collective servo  and elev. servo in 60 size heli's. The 8400 series JR servo has the bearings spaced farther apart than the older 4000 series which helps reduce the side loads. 

        The ball links on the JR set are a little tight and need to be free'd up a little to reduce drag. I haven't bought any in several years.

        The 8411 should hold up well on a 2M pattern plane without it , however it is piece of mind when hooked to a big rudder...........John G.

          -------------- Original message -------------- 

          Do we really need this output arm when using JR 8411 in the rudder (pull-pull system)? As far as I know, the main output gear is supported by two ball bearings.  

          Tahnks,

          Vicente

            -------------- Original message -------------- 

            I don't think JR makes them anymore but here is one that is the same thing by K+S for Helis:

            http://www.horizonhobby.com/Shop/ByCategory/Product/Default.aspx?ProdID=KSJ1370

            Troy
              ----- Original Message ----- 
              From: Ed Alt 
              To: discussion at nsrca.org 
              Sent: Tuesday, November 22, 2005 8:27 PM
              Subject: JR output arm stabilizers


              Does anyone know if these are still available?  These were a rectangular metal bracket that went around the servo, over the mounting flanges.  This bracket held a post with a ball end, which connected to a ball ended bolt for the servo arm, via an arm with swivel joints at each end. 

              Thanks
              Ed

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.f3a.us/pipermail/nsrca-discussion/attachments/20051123/3a87cd1c/attachment.html