Rudder pull-pull?

[Kurt Bozarth]

Crossing the lines can lead to the greatest differential when the rudder is
deflected.  The latest Fly RC mag has a pretty good article on the subject.

Kurt

-----Original Message-----
From: discussion-request at nsrca.org [mailto:discussion-request at nsrca.org] On
Behalf Of wgalligan
Sent: Sunday, May 01, 2005 6:43 PM
To: discussion at nsrca.org
Subject: Re: Rudder pull-pull?

Tom,

I use Kevlar pull lines and cross them to get a good line form the servo to
the exit at the back of the fuse.  I guess if you are using a coated wire
line there should be no problem.

Wayne G.

----- Original Message -----
From: "Koenig, Tom" <Tom.Koenig at actewagl.com.au>
To: "Discussion" <discussion at nsrca.org>
Sent: Sunday, May 01, 2005 7:24 PM
Subject: Rudder pull-pull?



Hi again all,

So what's the verdict with the Rudder pull-pulls? I'm about to cross that
bridge again this evening. This time I was considering crossing over the
wires/chord/trace to get better geometry. I'm a little paranoid about
crossing the wires( should I use the 'metallic' variety) as I think they
might touch using this method. The resulting 'noise' might not be desirable
to the radio.

The Du-Bro stuff is aesthetically pleasing ( small fittings etc) but
stretches. Kevlar is good-just a pain to fit-off and uses the bigger uglier
eyelets and/ but it too stretches ( maybe through the fittings?).

I've now got some SIG .015 C/L cable but I'm not to keen on fitting it
either. It is stainless and un-sheathed. Cant quite work out how to fit it
off. Soldering (soft) has been unsuccessful sofar. Crimping might look too
much like a hit and miss affair.

The servo end ( horns) seems to be another area of concern I have. I've
resorted to making a horn from circuit board to get a 2" spacing and
screwing it to the top of the existing horn ala MK style.

All in all I'm not to comfortable with any of my options...I'm yet to find
THE set up. I too want to eliminate stretch.

What are you guys doing out there in Pattern world ...I know its a silly,
and to some degree an elementary question, but I just need to find a better
way.

Thanks for any ideas or solutions.

Tom

************************************************************************
*PLEASE NOTE*  This email and any attachments may
be confidential. If received in error, please delete all
copies and advise the sender. The reproduction or
dissemination of this email or its attachments is
prohibited without the consent of the sender.

WARNING RE VIRUSES:  Our computer systems sweep
outgoing email to guard against viruses, but no warranty
is given that this email or its attachments are virus free.
Before opening or using attachments, please check for
viruses.  Our liability is limited to the re-supply of any
affected attachments.

Any views expressed in this message are those of the
individual sender, except where the sender expressly,
and with authority, states them to be the views of the
organisation.
************************************************************************
================To access the email archives for this list, go to
http://lists.f3a.us/pipermail/nsrca-discussion/
To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.

List members email returned for mailbox full will be removed from the list.





=================================================
To access the email archives for this list, go to
http://lists.f3a.us/pipermail/nsrca-discussion/
To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.

List members email returned for mailbox full will be removed from the list.


=================================================
To access the email archives for this list, go to
http://lists.f3a.us/pipermail/nsrca-discussion/
To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.

List members email returned for mailbox full will be removed from the list.