[NSRCA-discussion] securing servo wires

[dwaynenancy]

Be sure and get the floss that is not waxed.  You can also use the 
string that is used to be used for cable ties instead ot the plastic 
ones used today.  Dwayne

Bob Richards wrote:

> Instead of nylon fishing line, try dental floss.
>
> */Dean Pappas <d.pappas at kodeos.com>/* wrote:
>
>     Hi Guys.
>     How about a nylon fishhing line loop that passes through all the
>     connectors, between two of the wires in the connector, and around
>     the RX?
>     I've never done anything like this, but now that I think of it, I
>     like the idea.
>
>     Dean
>
>     Dean Pappas
>     Sr. Design Engineer
>     Kodeos Communications
>     111 Corporate Blvd.
>     South Plainfield, N.J. 07080
>     (908) 222-7817 phone
>     (908) 222-2392 fax
>     d.pappas at kodeos.com
>
>
>     -----Original Message-----
>     From: nsrca-discussion-bounces at lists.nsrca.org
>     [mailto:nsrca-discussion-bounces at lists.nsrca.org]On Behalf Of Ken
>     Thompson
>     Sent: Thursday, December 15, 2005 5:56 AM
>     To: NSRCA Mailing List
>     Subject: Re: [NSRCA-discussion] securing servo wires
>
>
>     David,!
>
>     I usually fold the wires down over the top of my receiver and
>     secure them
>     with a rubber band, around the receiver and wires, fairly snug.
>     Make sure you leave enough wire so as not to bind the wire against
>     the
>     connector.
>     Install as usual, sounds simple but it works for me.
>
>     Ken
>     ----- Original Message -----
>     From: "David Flynt"
>     To:
>     Sent: Wednesday, December 14, 2005 10:51 PM
>     Subject: [NSRCA-discussion] securing servo wires
>
>
>     > Can anybody suggest a good way to help prevent servo wires from
>     pulling
>     > out
>     > of a receiver? I have never paid attention to this, and never
>     really had
>     > a
>     > problem except one time one of my elevator servo wires pulled
>     loose. I
>     > was
>     > fortunate to have half an elevator remaining and enough control
>     to land.
>     > But now I only use a single elevator servo.
>     >
>     > I typically use either JR r770 or r649 receivers.
>     >
>     > Any ideas would be appreciated.
>     >
>     > Thanks,
>     >
>     > David Flynt
>     >
>     > _______________________________________________
>     > NSRCA-discussion mailing list
>     > NSRCA-discussion at lists.nsrca.org
>     > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
>     _______________________________________________
>     NSRCA-discussion mailing list
>     NSRCA-discussion at lists.nsrca.org
>     http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
>     _______________________________________________
>     NSRCA-discussion mailing list
>     NSRCA-discussion at lists.nsrca.org
>     http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
>
>------------------------------------------------------------------------
>
>_______________________________________________
>NSRCA-discussion mailing list
>NSRCA-discussion at lists.nsrca.org
>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
>------------------------------------------------------------------------
>
>No virus found in this incoming message.
>Checked by AVG Free Edition.
>Version: 7.1.371 / Virus Database: 267.13.13/200 - Release Date: 12/14/2005
>
>  
>