Finishing

[Koenig, Tom]

No, No No...I was referring to the clear coat acting as a fuel proofing agent. Createx, as far as I know, by itself is not fuel proof at all.

But a conventional Clear over Base system will now not have any potential problems in an electrified outfit.......as it can do in a conventional 30% nitro burning YS machine.

Tom


-----Original Message-----
From: discussion-request at nsrca.org [mailto:discussion-request at nsrca.org]On Behalf Of Lance Van Nostrand
Sent: Monday, 12 December 2005 3:28 PM
To: discussion at nsrca.org
Subject: Re: Finishing


So this stuff is fuel proof?  Does it mix with a hardener or just cure with heat and water evaportation?  I'm skeptical that something that doesn't crosslink can be fuel proof, but maybe this stuff actually cures into polymer chains like polyU glue?
--Lance


----- Original Message -----
From: Koenig, Tom <mailto:Tom.Koenig at actewagl.com.au> 
To: discussion at nsrca.org
Sent: Sunday, December 11, 2005 7:45 PM
Subject: RE: Finishing

Steve/all,

I have clear coated a few planes for a friend of mine who uses the createx stuff. I just used an automotive two pack clear coat. It comes up ok but is very dependent on the skill of the 'createx' applicator! If it is applied to dry and the prep work sucks-no amount of clear coat will make it look good.
Infact I was blamed for the paint job!!! Nowadays-he takes his planes to a professional auto shop-and they charge him a packet of money with the same result. Works for me as its less possible exposure to the nasty stuff.

I also believe there may be some adhesion problems with createx if not applied correctly.His stuff I've seen flake off ( i.e.; prep work!!!)

My recommendation is to use the 'clear over base' system and just minimize the clear as it now no longer serves as a fuel proofing agent.

Tom

-----Original Message-----
From: discussion-request at nsrca.org [mailto:discussion-request at nsrca.org]On Behalf Of Steven Maxwell
Sent: Monday, 12 December 2005 12:24 PM
To: discussion at nsrca.org
Subject: RE: Finishing


 Nat over the last couple of years I have been playing with Createx Auto Airs http://www.autoaircolors.com/ they are water base paints that is used for airbrushing although they do need a clear coat to bring to a shine. They are extremely light and easy to use they just look dull as applied. They can be mixed and matched to anything and have 128 colors to choose from, theres a dealer you'll find on there dealer page called Dixie Art Supply in New Orleans  http://www.dixieart.com/CreatexAutoAir.html I have only cleared with Lustre Kote which is not recomended by them, but maybe for the electrics you won't need the clear. Good luck.
 Steve Maxwell



----- Original Message -----
From: Nat Penton <mailto:natpenton at centurytel.net> 
To: discussion at nsrca.org
Sent: 12/11/2005 10:28:25 PM
Subject: Finishing


I don't know whether to use polyurethane, latex, watercolor or crayola. These electrics present all kinds of problems.
                                                        Nat

************************************************************************
*PLEASE NOTE* This email and any attachments may
be confidential. If received in error, please delete all
copies and advise the sender. The reproduction or
dissemination of this email or its attachments is
prohibited without the consent of the sender.

WARNING RE VIRUSES: Our computer systems sweep
outgoing email to guard against viruses, but no warranty
is given that this email or its attachments are virus free.
Before opening or using attachments, please check for
viruses. Our liability is limited to the re-supply of any
affected attachments.

Any views expressed in this message are those of the
individual sender, except where the sender expressly,
and with authority, states them to be the views of the
organisation.
************************************************************************




************************************************************************
*PLEASE NOTE*  This email and any attachments may
be confidential. If received in error, please delete all
copies and advise the sender. The reproduction or
dissemination of this email or its attachments is
prohibited without the consent of the sender.

WARNING RE VIRUSES:  Our computer systems sweep
outgoing email to guard against viruses, but no warranty
is given that this email or its attachments are virus free.
Before opening or using attachments, please check for
viruses.  Our liability is limited to the re-supply of any
affected attachments.

Any views expressed in this message are those of the
individual sender, except where the sender expressly,
and with authority, states them to be the views of the
organisation.
************************************************************************
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.f3a.us/pipermail/nsrca-discussion/attachments/20051212/c30b9eb1/attachment.html