Elev. Pull pull Question

[Bob Pastorello]

Depends on whether it's in Texas, or the United States.

Bob Pastorello
NSRCA 199  AMA 46373
rcaerobob at cox.net
www.rcaerobats.net


  ----- Original Message ----- 
  From: Wayne Galligan 
  To: discussion at nsrca.org 
  Sent: Friday, November 26, 2004 1:45 PM
  Subject: Re: Elev. Pull pull Question


  How much offset could an offset have if an offset had no Ackerman?

    ----- Original Message ----- 
    From: Bob Pastorello 
    To: discussion at nsrca.org 
    Sent: Friday, November 26, 2004 12:28 PM
    Subject: Re: Elev. Pull pull Question


    MOST Excellent, Keith.  Rational, understandable, and mathematically-proven.  Thanks for sharing that.

    BTW - my offset horns DO have "Ackerman", but one side of ONE elev. half had 1/16" LESS Ackerman, and it was costing almost a degree difference at full deflection.

    Bob Pastorello
    NSRCA 199  AMA 46373
    rcaerobob at cox.net
    www.rcaerobats.net


      ----- Original Message ----- 
      From: Keith Black 
      To: discussion at nsrca.org 
      Sent: Friday, November 26, 2004 11:53 AM
      Subject: Re: Elev. Pull pull Question


      In addition to the height of the control horn we must also considered where the control horn "pivot point" is in relation to the hinge line, not where the control horn is physically located on the control surface. In other words, your control horn has a hole where the clevis connects to it. This clevis rotates in the control horn as it's pulled back and forth. If this rotation point on one elevator half is at a different point from the other elevator half then the throws will not bee the same.

      Here is an EXCELLENT article on what is know as the Ackerman effect and how this applies to our pull-pull setups. For me, understanding this was instrumental in getting a real grasp on pull-pull systems.

      http://members.cox.net/bdfelice/Ackerman/ackerman.htm

      Keith Black
        ----- Original Message ----- 
        From: George Kennie 
        To: discussion at nsrca.org 
        Sent: Friday, November 26, 2004 11:21 AM
        Subject: Re: Elev. Pull pull Question


        Bob, 
        That sounds backward to me. If the bolt on the further traveling half is further forward, then it should be going over-center sooner generating less linear travel than the half on the other side. My bet is on the inboard hinge slot not centered (low) on that side. On mine I had some off center hinge slots. 
        Georgie 
        Daniel J. Hamlett wrote: 

            Yes 
            ----- Original Message -----
            From: Bob Pastorello
            To: discussion at nsrca.org
            Sent: Friday, November 26, 2004 9:38 AM
            Subject: Re: Elev. Pull pull Question
             Yep.  Same distance OUT from surface.  However, just checking things - again - the elevator that is travelling too far also has the control takeoff about 1/16" further FORWARD relative to the hinge line than the other half.    Could this do it? 
            Bob Pastorello 
            NSRCA 199  AMA 46373 
            rcaerobob at cox.net 
            www.rcaerobats.net   

              ----- Original Message -----
              From: Tom Hinton
              To: discussion at nsrca.org
              Sent: Friday, November 26, 2004 8:07 AM
              Subject: Re: Elev. Pull pull Question
               Are both the horns on the bottom the same distance from the surface, same amount of threads? 
                ----- Original Message -----
                From: Bob Pastorello
                To: NSRCA
                Sent: Friday, November 26, 2004 8:58 AM
                Subject: Elev. Pull pull Question
                 May seem obvious, but I could use some help here....setting up my Excelleron, centers are okay, cable tensions are pretty close, centering is good.  Up elevator is fine, on Down elevator, ONE elevator moves farther, but they track together except at the endpoint, as close as I can tell. Anyone have suggestions on how I'd fine tune this out...??Hope everyone had a great T-day!! 
                Bob Pastorello 
                NSRCA 199  AMA 46373 
                rcaerobob at cox.net 
                www.rcaerobats.net  

          
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.f3a.us/pipermail/nsrca-discussion/attachments/20041126/0bc62d1f/attachment-0001.html